; ; RTL8186 system configuration file for vpn-gateway mode ; ; $Id: config-vpn.txt,v 1.1.1.1 2005/03/02 12:56:08 richardh Exp $ ; ; Copyright (c) Realtek Semiconductor Corp., 2004. All Rights Reserved. ; Hardware setting ; --------------------------------------------------------------------------- HW_NIC0_ADDR=00e04c818621 ; Ethernet LAN address HW_NIC1_ADDR=00e04c818622 ; WAN mac address ; WLAN0 interface. Note: "WLAN0" means 8186 embedded wlan controller HW_WLAN0_WLAN_ADDR=00e04c818621 ; wlan0 MAC address HW_WLAN0_REG_DOMAIN=1 ; FCC=1, IC=2, ETSI=3, SPAIN=4, FRANCE=5, MKK=6 HW_WLAN0_RF_TYPE=7 ; 7 - RTL8225(11b/g), 8 - RTL8255(11b/g/a) HW_WLAN0_TX_POWER_CCK=8 8 8 8 8 8 8 8 8 8 8 8 8 8 ; channel 1~14 Tx power for CCK HW_WLAN0_TX_POWER_OFDM=14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 ; channel 1~14 Tx power for OFDM HW_WLAN0_ANT_DIVERSITY=0 ; 1 - enable diversity, 0 - disable diversity HW_WLAN0_TX_ANT=0 ; Tx antenna, 0 - A , 1 - B HW_WLAN0_INIT_GAIN=4 ; baseband initial gain value HW_WLAN0_CCA_MODE=0 ; CCA mode HW_WLAN0_LED_TYPE=2 ; Except 0/1 is hardware wired, others are controlled by software ; WLAN-LED0 WLAN-LED1 ; ============================================================= ; 0 tx rx ; 1 enabled/tx/rx N/A ; 2 link tx/rx (data, management packet) ; 3 link/tx/rx N/A (data packet) ; 4 link tx-data/rx-data (data packet) ; 5 link/tx-data/rx-data N/A (data packet) ; 6 enable tx/rx (data packet) ; 7 enable/tx-data/rx-data N/A (data packet) ; WLAN1 interface. Note:"WLAN1" means external wlan controller connected through PCI. ; If you do not use it, you can ignore the following setting. HW_WLAN1_WLAN_ADDR=00e04c818623 ; wlan0 MAC address HW_WLAN1_REG_DOMAIN=1 ; FCC=1, IC=2, ETSI=3, SPAIN=4, FRANCE=5, MKK=6 HW_WLAN1_RF_TYPE=7 ; 7 - RTL8225(11b/g), 8 - RTL8255(11b/g/a) HW_WLAN1_TX_POWER_CCK=8 8 8 8 8 8 8 8 8 8 8 8 8 8 ; channel 1~14 Tx power for CCK HW_WLAN1_TX_POWER_OFDM=14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 ; channel 1~14 Tx power for OFDM HW_WLAN1_ANT_DIVERSITY=0 ; 1 - enable diversity, 0 - disable diversity HW_WLAN1_TX_ANT=0 ; Tx antenna, 0 - A , 1 - B HW_WLAN1_INIT_GAIN=4 ; baseband initial gain value HW_WLAN1_CCA_MODE=0 ; CCA mode HW_WLAN1_LED_TYPE=2 ; Except 0/1 is hardware wired, others are controlled by software ; WLAN-LED0 WLAN-LED1 ; ============================================================= ; 0 tx rx ; 1 enabled/tx/rx N/A ; 2 link tx/rx (data, management packet) ; 3 link/tx/rx N/A (data packet) ; 4 link tx-data/rx-data (data packet) ; 5 link/tx-data/rx-data N/A (data packet) ; 6 enable tx/rx (data packet) ; 7 enable/tx-data/rx-data N/A (data packet) ; Firmware factory-default setting ; --------------------------------------------------------------------------- ; wan interface DEF_WAN_MAC_ADDR=000000000000 ; clone mac DEF_WAN_IP_ADDR=172.1.1.1 ; ip address DEF_WAN_SUBNET_MASK=255.255.255.0 ; subnet mask of DEF_WAN_DEFAULT_GATEWAY=172.1.1.254 ; default gateway DEF_WAN_DHCP=1 ; protocol, 0 - fixed ip, 1 - dhcp client, 3 - PPPoE, 4 - PPTP DEF_DNS_MODE=0 ; DNS mode, 0 - auto, 1 - manual DEF_DNS1=0.0.0.0 ; DNS value, refer when DNS is set to auto DEF_DNS2=0.0.0.0 DEF_DNS3=0.0.0.0 DEF_PPP_USER_NAME= ; PPPoE login user name DEF_PPP_PASSWORD= ; PPPoE login user passwowrd DEF_PPP_IDLE_TIME=300 ; idle time of PPPoE (in sec) DEF_PPP_CONNECT_TYPE=0 ; PPPoE connect type, 0 - continuous, 1 - connet on demand, 2 - manual DEF_PPP_MTU_SIZE=1452 ; PPPoE MTU size (1400-1492) DEF_PPTP_IP_ADDR=172.1.1.2 ; PPTP local IP address DEF_PPTP_SUBNET_MASK=255.255.255.0 ; PPTP subnet mask DEF_PPTP_SERVER_IP_ADDR=172.1.1.1 ; PPTP server IP address DEF_PPTP_USER_NAME="" ; PPTP login user name DEF_PPTP_PASSWORD="" ; PPTP login user passwowrd DEF_PPTP_MTU_SIZE=1452 ; PPTP MTU size (1400-1492) DEF_NTP_ENABLED=0 ; NTP flag, 0 - disable, 1 - enable DEF_NTP_SERVER_ID=0 ; 0 - selected from menu, 1 - input manually DEF_NTP_TIMEZONE="-8 4" ; Taipei timezone DEF_NTP_SERVER_IP1=0.0.0.0 ; server IP addr1, selected from menu list DEF_NTP_SERVER_IP2=0.0.0.0 ; server IP addr2, manual input DEF_DDNS_ENABLED=0 ; DDNS flag, 0 - disable, 1 - enable DEF_DDNS_TYPE=0 ; DDNS type, 0 - DynDNS, 1 - TZO DEF_DDNS_DOMAIN_NAME="host.dyndns.org" ; host domain name DEF_DDNS_USER= ; DDNS user name DEF_DDNS_PASSWORD= ; DDNS user password DEF_IPSECTUNNEL_ENABLED=0 ; ipsec gateway flag, 0 - disable, 1 - enabled DEF_IPSECTUNNEL_TBL_NUM=0 ; ipsec entry number ; Firewall DEF_PORTFW_ENABLED=0 ; port-forwarding flag, 0 - disable, 1 - enable DEF_PORTFW_TBL_NUM=0 ; existing port-fowarding table entry number DEF_IPFILTER_ENABLED=0 ; ip-filtering flag, 0 - disable, 1 - enable DEF_IPFILTER_TBL_NUM=0 ; existing ip-filtering table entry number DEF_PORTFILTER_ENABLED=0 ; port-filtering flag, 0 - disable, 1 - enable DEF_PORTFILTER_TBL_NUM=0 ; existing port-filtering table entry number DEF_MACFILTER_ENABLED=0 ; mac-filtering flag, 0 - disable, 1 - enable DEF_MACFILTER_TBL_NUM=0 ; existing mac-filtering table entry number DEF_TRIGGERPORT_ENABLED=0 ; trigger-port flag, 0 - disable, 1 - enable DEF_TRIGGERPORT_TBL_NUM=0 ; existing trigger-port table entry number DEF_DMZ_ENABLED=0 ; DMZ flag, 0 - disable, 1 - enable DEF_DMZ_HOST=0.0.0.0 ; DMZ ip address DEF_UPNP_ENABLED=0 ; uPNP flag, 0 - disable, 1 - enable DEF_WEB_WAN_ACCESS_ENABLED=0 ; web access on WAN, 0 - disable, 1 - enable ; LAN interface DEF_DEVICE_NAME="RTL8186" ; device logical namem, referred by uPNP IGD name DEF_ELAN_MAC_ADDR=000000000000 ; Ethernet MAC clone address DEF_IP_ADDR=192.168.1.254 ; ip address DEF_DHCP_CLIENT_START=192.168.1.100 ; DHCP client range - start address DEF_DHCP_CLIENT_END=192.168.1.200 ; DHCP client range - end address DEF_SUBNET_MASK=255.255.255.0 ; subnet mask DEFAULT_GATEWAY=0.0.0.0 ; default route DEF_DHCP=2 ; DHCP mode, 0 - fixed ip, 1 - dhcp client, 2 - dhcp server DEF_STP_ENABLED=0 ; spanning tree protocol flag, 0 - disable, 1 - enable ; web management DEF_SUPER_NAME=super ; supervisor user name, if NULL, supervisor account will be disabled DEF_SUPER_PASSWORD=super ; supervisor user password, if NULL, supervisor account will be disabled DEF_USER_NAME= ; user name DEF_USER_PASSWORD= ; user password DEF_SCRLOG_ENABLED=0 ; system Log flag, 0 - disabled, 1 - enabled (not supported yet) DEF_AUTODISCOVERY_ENABLED=1 ; auto-discovery flag, 0 - disabled, 1 - enabled DEF_OP_MODE=0 ; operation mode, 0 - gateway mode (LAN:br0(eth0+wlan0), WAN:eth1) ; 1 - bridge mode (LAN:br0(eth0+eth1+wlan0)) ; 2 - WISP(wireless ISP) mode (LAN:br0(eth0+eth1), WAN:wlan0) DEF_WISP_WAN_ID=0 ; wlan interface id for WISP mode. 0 - use wlan0 as WAN and OP_MODE is set WISP. ; 1 - use wlan0 as WAN and OP_MODE is set WISP. ; WLAN0 interface. Note: "WLAN0" means 8186 embedded wlan controller DEF_WLAN0_WLAN_MAC_ADDR=000000000000; clone mac address DEF_WLAN0_SSID=RTL8186-VPN-GW ; SSID DEF_WLAN0_CHANNEL=11 ; channel number DEF_WLAN0_WEP=0 ; WEP flag, 0 - WEP disable, 1 - WEP-64bits, 2 - WEP-128bits DEF_WLAN0_WEP64_KEY1=0000000000 ; WEP-64bits key1~key4 DEF_WLAN0_WEP64_KEY2=0000000000 DEF_WLAN0_WEP64_KEY3=0000000000 DEF_WLAN0_WEP64_KEY4=0000000000 DEF_WLAN0_WEP128_KEY1=00000000000000000000000000 ; WEP-128bits key1~key4 DEF_WLAN0_WEP128_KEY2=00000000000000000000000000 DEF_WLAN0_WEP128_KEY3=00000000000000000000000000 DEF_WLAN0_WEP128_KEY4=00000000000000000000000000 DEF_WLAN0_WEP_DEFAULT_KEY=0 ; default tx key id (0-3) DEF_WLAN0_WEP_KEY_TYPE=1 ; key type, 0 - ASCII, 1 - hex DEF_WLAN0_FRAG_THRESHOLD=2346 ; fragment threshold, 256-2346 DEF_WLAN0_RTS_THRESHOLD=2347 ; RTS threshold, 0 - 2347 DEF_WLAN0_BASIC_RATES=15 ; basic rate, bit0~bit11 for rate 1,2,5.5,11,6,9,12,18,24,36,48,54M DEF_WLAN0_SUPPORTED_RATES=4095 ; supported rate, bit0~bit11 for rate 1,2,5.5,11,6,9,12,18,24,36,48,54M DEF_WLAN0_BEACON_INTERVAL=100 ; beacon interval in ms(20-1024) DEF_WLAN0_PREAMBLE_TYPE=0 ; preamble type, 0 - long preamble, 1 - short preamble DEF_WLAN0_AUTH_TYPE=2 ; athentication type, 0 - open system, 1 - shared key, 2 - auto (both) DEF_WLAN0_HIDDEN_SSID=0 ; hidden ssid, 0 - disable, 1 - enable DEF_WLAN0_WLAN_DISABLED=0 ; wlan interface flag, 0 - wlan enabled, 1 - wlan disabled DEF_WLAN0_INACTIVITY_TIME=30000 ; wlan client inactivity time (in 10ms) DEF_WLAN0_RATE_ADAPTIVE_ENABLED=1 ; tx rate adaptive enable/disable, 1 - enabled, 0 - disabled DEF_WLAN0_MACAC_NUM=0 ; existing table entry number for mac access control DEF_WLAN0_MACAC_ENABLED=0 ; wlan mac access control flag, 0 - disable, 1 - enable DEF_WLAN0_DTIM_PERIOD=1 ; DTIM period DEF_WLAN0_BLOCK_RELAY=0 ; blocking packets between wireless client (relay), ; 0 - disabled, 1 - block relay, 2 - block relay but passup DEF_WLAN0_BAND=3 ; bit mask of band selection, 1-11b, 2-11g, 4-11a DEF_WLAN0_FIX_RATE=0 ; fixed data rate, 0-disable, bit0~bit11 for rate 1,2,5.5,11,6,9,12,18,24,36,48,54M DEF_MACAC_NUMMODE=0 ; operation mode, 0-AP, 1-client, 2-WDS, 3-AP+WDS DEF_WLAN0_ENCRYPT=0 ; 0 - Encrypt disabled, 1 - WEP, 2 - WPA, 4 - WPA2, 6 - WPA2 mixed DEF_WLAN0_ENABLE_1X=0 ; 802.1x flag, 0 - disabled, 1 - enabled DEF_WLAN0_WPA_AUTH=2 ; WPA authentication type, 1 - WPA-Radius, 2 - PSK DEF_WLAN0_WPA_CIPHER_SUITE=1 ; WPA Cipher suite, 1 - TKIP, 2 - AES DEF_WLAN0_WPA_PSK= ; WPA PSK value DEF_WLAN0_WPA_GROUP_REKEY_TIME=86400; group key update time (in sec) DEF_WLAN0_RS_IP=0.0.0.0 ; Radius serverIP address DEF_WLAN0_RS_PORT=1812 ; Radius server port DEF_WLAN0_RS_PASSWORD= ; Radius server password DEF_WLAN0_RS_MAXRETRY=3 ; Max retry of Radius server DEF_WLAN0_RS_INTERVAL_TIME=5 ; Interval time of retry DEF_WLAN0_WPA2_PRE_AUTH=0 ; WPA2 pre-authentication flag, 0 - disable, 1 - enable DEF_WLAN0_WPA2_CIPHER_SUITE=2 ; WPA Cipher suite, 1 - TKIP, 2 - AES DEF_WLAN0_MACCLONE_ENABLED=0 ; wlan mac clone flag (client mode used), 0 - disable, 1 - enable DEF_WLAN0_IAPP_DISABLED=0 ; IAPP flag, 0 - IAPP enabled, 1 - IAPP disabled DEF_WLAN0_PROTECTION_DISABLED=0 ; 802.11g protection mode flag, 0 - protection enable, 1 - protection disabled DEF_WLAN0_WDS_ENABLED=0 ; WDS flag, 0 - disable, 1 - enable DEF_WLAN0_WDS_NUM=0 ; existing table entry number for WDS AP DEF_WLAN0_WDS_WEP=0 ; WDS WEP flag, 0 - WEP disable, 1 - WEP-64bits, 2 - WEP-128bits, 3-TKIP, 4-AES DEF_WLAN0_WDS_WEP64_KEY1=0000000000 ; WEP-64bits key1~key4 DEF_WLAN0_WDS_WEP64_KEY2=0000000000 DEF_WLAN0_WDS_WEP64_KEY3=0000000000 DEF_WLAN0_WDS_WEP64_KEY4=0000000000 DEF_WLAN0_WDS_WEP128_KEY1=00000000000000000000000000 ; WEP-128bits key1~key4 DEF_WLAN0_WDS_WEP128_KEY2=00000000000000000000000000 DEF_WLAN0_WDS_WEP128_KEY3=00000000000000000000000000 DEF_WLAN0_WDS_WEP128_KEY4=00000000000000000000000000 DEF_WLAN0_WDS_WEP_DEFAULT_KEY=0 ; default tx key id (0-3) DEF_WLAN0_WDS_WEP_KEY_TYPE=1 ; key type, 0 - ASCII, 1 - hex DEF_WLAN0_WDS_PSK_FORMAT=0 ; psk format, 0 - ACSII, 1 - hex DEF_WLAN0_WDS_PSK= ; psk value DEF_WLAN0_EASYCFG_ENABLED=1 ; easy-config flag, 0-disable, 1-enable DEF_WLAN0_EASYCFG_MODE=1 ; easy-config mode, 1 - button, 2 - QA DEF_WLAN0_EASYCFG_ALG_REQ=32 ; request encryption (client mode), 4-TKIP, 32-AES DEF_WLAN0_EASYCFG_ALG_SUPP=36 ; support encryption (AP mode), TKIP+AES DEF_WLAN0_EASYCFG_SCAN_SSID=REALTEK_EASY_CONFIG ; SSID used by easy-config ; WLAN1 interface. Note:"WLAN1" means external wlan controller connected through PCI. ; If you do not use it, you can ignore the following setting. DEF_WLAN1_WLAN_MAC_ADDR=000000000000; clone mac address DEF_WLAN1_SSID=RTL8186-VPN-GW ; SSID DEF_WLAN1_CHANNEL=11 ; channel number DEF_WLAN1_WEP=0 ; WEP flag, 0 - WEP disable, 1 - WEP-64bits, 2 - WEP-128bits DEF_WLAN1_WEP64_KEY1=0000000000 ; WEP-64bits key1~key4 DEF_WLAN1_WEP64_KEY2=0000000000 DEF_WLAN1_WEP64_KEY3=0000000000 DEF_WLAN1_WEP64_KEY4=0000000000 DEF_WLAN1_WEP128_KEY1=00000000000000000000000000 ; WEP-128bits key1~key4 DEF_WLAN1_WEP128_KEY2=00000000000000000000000000 DEF_WLAN1_WEP128_KEY3=00000000000000000000000000 DEF_WLAN1_WEP128_KEY4=00000000000000000000000000 DEF_WLAN1_WEP_DEFAULT_KEY=0 ; default tx key id (0-3) DEF_WLAN1_WEP_KEY_TYPE=1 ; key type, 0 - ASCII, 1 - hex DEF_WLAN1_FRAG_THRESHOLD=2346 ; fragment threshold, 256-2346 DEF_WLAN1_RTS_THRESHOLD=2347 ; RTS threshold, 0 - 2347 DEF_WLAN1_BASIC_RATES=15 ; basic rate, bit0~bit11 for rate 1,2,5.5,11,6,9,12,18,24,36,48,54M DEF_WLAN1_SUPPORTED_RATES=4095 ; supported rate, bit0~bit11 for rate 1,2,5.5,11,6,9,12,18,24,36,48,54M DEF_WLAN1_BEACON_INTERVAL=100 ; beacon interval in ms(20-1024) DEF_WLAN1_PREAMBLE_TYPE=0 ; preamble type, 0 - long preamble, 1 - short preamble DEF_WLAN1_AUTH_TYPE=2 ; athentication type, 0 - open system, 1 - shared key, 2 - auto (both) DEF_WLAN1_HIDDEN_SSID=0 ; hidden ssid, 0 - disable, 1 - enable DEF_WLAN1_WLAN_DISABLED=0 ; wlan interface flag, 0 - wlan enabled, 1 - wlan disabled DEF_WLAN1_INACTIVITY_TIME=30000 ; wlan client inactivity time (in 10ms) DEF_WLAN1_RATE_ADAPTIVE_ENABLED=1 ; tx rate adaptive enable/disable, 1 - enabled, 0 - disabled DEF_WLAN1_MACAC_NUM=0 ; existing table entry number for mac access control DEF_WLAN1_MACAC_ENABLED=0 ; wlan mac access control flag, 0 - disable, 1 - enable DEF_WLAN1_DTIM_PERIOD=1 ; DTIM period DEF_WLAN1_BLOCK_RELAY=0 ; blocking packets between wireless client (relay), ; 0 - disabled, 1 - block relay, 2 - block relay but passup DEF_WLAN1_BAND=3 ; bit mask of band selection, 1-11b, 2-11g, 4-11a DEF_WLAN1_FIX_RATE=0 ; fixed data rate, 0-disable, bit0~bit11 for rate 1,2,5.5,11,6,9,12,18,24,36,48,54M DEF_MACAC_NUMMODE=0 ; operation mode, 0-AP, 1-client, 2-WDS, 3-AP+WDS DEF_WLAN1_ENCRYPT=0 ; 0 - Encrypt disabled, 1 - WEP, 2 - WPA, 4 - WPA2, 6 - WPA2 mixed DEF_WLAN1_ENABLE_1X=0 ; 802.1x flag, 0 - disabled, 1 - enabled DEF_WLAN1_WPA_AUTH=2 ; WPA authentication type, 1 - WPA-Radius, 2 - PSK DEF_WLAN1_WPA_CIPHER_SUITE=1 ; WPA Cipher suite, 1 - TKIP, 2 - AES DEF_WLAN1_WPA_PSK= ; WPA PSK value DEF_WLAN1_WPA_GROUP_REKEY_TIME=86400; group key update time (in sec) DEF_WLAN1_RS_IP=0.0.0.0 ; Radius serverIP address DEF_WLAN1_RS_PORT=1812 ; Radius server port DEF_WLAN1_RS_PASSWORD= ; Radius server password DEF_WLAN1_RS_MAXRETRY=3 ; Max retry of Radius server DEF_WLAN1_RS_INTERVAL_TIME=5 ; Interval time of retry DEF_WLAN1_WPA2_PRE_AUTH=0 ; WPA2 pre-authentication flag, 0 - disable, 1 - enable DEF_WLAN1_WPA2_CIPHER_SUITE=2 ; WPA Cipher suite, 1 - TKIP, 2 - AES DEF_WLAN1_MACCLONE_ENABLED=0 ; wlan mac clone flag (client mode used), 0 - disable, 1 - enable DEF_WLAN1_IAPP_DISABLED=0 ; IAPP flag, 0 - IAPP enabled, 1 - IAPP disabled DEF_WLAN1_PROTECTION_DISABLED=0 ; 802.11g protection mode flag, 0 - protection enable, 1 - protection disabled DEF_WLAN1_WDS_ENABLED=0 ; WDS flag, 0 - disable, 1 - enable DEF_WLAN1_WDS_NUM=0 ; existing table entry number for WDS AP DEF_WLAN1_WDS_WEP=0 ; WDS WEP flag, 0 - WEP disable, 1 - WEP-64bits, 2 - WEP-128bits, 3-TKIP, 4-AES DEF_WLAN1_WDS_WEP64_KEY1=0000000000 ; WEP-64bits key1~key4 DEF_WLAN1_WDS_WEP64_KEY2=0000000000 DEF_WLAN1_WDS_WEP64_KEY3=0000000000 DEF_WLAN1_WDS_WEP64_KEY4=0000000000 DEF_WLAN1_WDS_WEP128_KEY1=00000000000000000000000000 ; WEP-128bits key1~key4 DEF_WLAN1_WDS_WEP128_KEY2=00000000000000000000000000 DEF_WLAN1_WDS_WEP128_KEY3=00000000000000000000000000 DEF_WLAN1_WDS_WEP128_KEY4=00000000000000000000000000 DEF_WLAN1_WDS_WEP_DEFAULT_KEY=0 ; default tx key id (0-3) DEF_WLAN1_WDS_WEP_KEY_TYPE=1 ; key type, 0 - ASCII, 1 - hex DEF_WLAN1_WDS_PSK_FORMAT=0 ; psk format, 0 - ACSII, 1 - hex DEF_WLAN1_WDS_PSK= ; psk value DEF_WLAN1_EASYCFG_ENABLED=1 ; easy-config flag, 0-disable, 1-enable DEF_WLAN1_EASYCFG_MODE=1 ; easy-config mode, 1 - button, 2 - QA DEF_WLAN1_EASYCFG_ALG_REQ=32 ; request encryption (client mode), 4-TKIP, 32-AES DEF_WLAN1_EASYCFG_ALG_SUPP=36 ; support encryption (AP mode), TKIP+AES DEF_WLAN1_EASYCFG_SCAN_SSID=REALTEK_EASY_CONFIG ; SSID used by easy-config ; Firmware current-used setting ; --------------------------------------------------------------------------- ; wan interface WAN_MAC_ADDR=000000000000 ; clone mac WAN_IP_ADDR=172.1.1.1 ; ip address WAN_SUBNET_MASK=255.255.255.0 ; subnet mask of WAN_DEFAULT_GATEWAY=172.1.1.254 ; default gateway WAN_DHCP=1 ; protocol, 0 - fixed ip, 1 - dhcp client, 3 - PPPoE, 4 - PPTP DNS_MODE=0 ; DNS mode, 0 - auto, 1 - manual DNS1=0.0.0.0 ; DNS value, refer when DNS is set to auto DNS2=0.0.0.0 DNS3=0.0.0.0 PPP_USER_NAME= ; PPPoE login user name PPP_PASSWORD= ; PPPoE login user passwowrd PPP_IDLE_TIME=300 ; idle time of PPPoE (in sec) PPP_CONNECT_TYPE=0 ; PPPoE connect type, 0 - continuous, 1 - connet on demand, 2 - manual PPP_MTU_SIZE=1452 ; PPPoE MTU size (1400-1492) PPTP_IP_ADDR=172.1.1.2 ; PPTP local IP address PPTP_SUBNET_MASK=255.255.255.0 ; PPTP subnet mask PPTP_SERVER_IP_ADDR=172.1.1.1 ; PPTP server IP address PPTP_USER_NAME="" ; PPTP login user name PPTP_PASSWORD="" ; PPTP login user passwowrd PPTP_MTU_SIZE=1452 ; PPTP MTU size (1400-1492) NTP_ENABLED=0 ; NTP flag, 0 - disable, 1 - enable NTP_SERVER_ID=0 ; 0 - selected from menu, 1 - input manually NTP_TIMEZONE="-8 4" ; Taipei timezone NTP_SERVER_IP1=0.0.0.0 ; server IP addr1, selected from menu list NTP_SERVER_IP2=0.0.0.0 ; server IP addr2, manual input DDNS_ENABLED=0 ; DDNS flag, 0 - disable, 1 - enable DDNS_TYPE=0 ; DDNS type, 0 - DynDNS, 1 - TZO DDNS_DOMAIN_NAME="host.dyndns.org" ; host domain name DDNS_USER= ; DDNS user name DDNS_PASSWORD= ; DDNS user password IPSECTUNNEL_ENABLED=0 ; ipsec gateway flag, 0 - disable, 1 - enabled IPSECTUNNEL_TBL_NUM=0 ; ipsec entry number ; Firewall PORTFW_ENABLED=0 ; port-forwarding flag, 0 - disable, 1 - enable PORTFW_TBL_NUM=0 ; existing port-fowarding table entry number IPFILTER_ENABLED=0 ; ip-filtering flag, 0 - disable, 1 - enable IPFILTER_TBL_NUM=0 ; existing ip-filtering table entry number PORTFILTER_ENABLED=0 ; port-filtering flag, 0 - disable, 1 - enable PORTFILTER_TBL_NUM=0 ; existing port-filtering table entry number MACFILTER_ENABLED=0 ; mac-filtering flag, 0 - disable, 1 - enable MACFILTER_TBL_NUM=0 ; existing mac-filtering table entry number TRIGGERPORT_ENABLED=0 ; trigger-port flag, 0 - disable, 1 - enable TRIGGERPORT_TBL_NUM=0 ; existing trigger-port table entry number DMZ_ENABLED=0 ; DMZ flag, 0 - disable, 1 - enable DMZ_HOST=0.0.0.0 ; DMZ ip address UPNP_ENABLED=0 ; uPNP flag, 0 - disable, 1 - enable WEB_WAN_ACCESS_ENABLED=0 ; web access on WAN, 0 - disable, 1 - enable ; LAN interface DEVICE_NAME="RTL8186" ; device logical namem, referred by uPNP IGD name ELAN_MAC_ADDR=000000000000 ; Ethernet MAC clone address IP_ADDR=192.168.1.254 ; ip address DHCP_CLIENT_START=192.168.1.100 ; DHCP client range - start address DHCP_CLIENT_END=192.168.1.200 ; DHCP client range - end address SUBNET_MASK=255.255.255.0 ; subnet mask DEFAULT_GATEWAY=0.0.0.0 ; default route DHCP=2 ; DHCP mode, 0 - fixed ip, 1 - dhcp client, 2 - dhcp server STP_ENABLED=0 ; spanning tree protocol flag, 0 - disable, 1 - enable ; web management SUPER_NAME=super ; supervisor user name, if NULL, supervisor account will be disabled SUPER_PASSWORD=super ; supervisor user password, if NULL, supervisor account will be disabled USER_NAME= ; user name USER_PASSWORD= ; user password ; system management SCRLOG_ENABLED=0 ; system Log flag, 0 - disabled, 1 - enabled (not supported yet) AUTODISCOVERY_ENABLED=1 ; auto-discovery flag, 0 - disabled, 1 - enabled OP_MODE=0 ; operation mode, 0 - gateway mode (LAN:br0(eth0+wlan0), WAN:eth1) ; 1 - bridge mode (LAN:br0(eth0+eth1+wlan0)) ; 2 - WISP(wireless ISP) mode (LAN:br0(eth0+eth1), WAN:wlan0) WISP_WAN_ID=0 ; wlan interface id for WISP mode. 0 - use wlan0 as WAN and OP_MODE is set WISP. ; 1 - use wlan0 as WAN and OP_MODE is set WISP. ; WLAN0 interface. Note: "WLAN0" means 8186 embedded wlan controller WLAN0_WLAN_MAC_ADDR=000000000000; clone mac address WLAN0_SSID=RTL8186-VPN-GW ; SSID WLAN0_CHANNEL=11 ; channel number WLAN0_WEP=0 ; WEP flag, 0 - WEP disable, 1 - WEP-64bits, 2 - WEP-128bits WLAN0_WEP64_KEY1=0000000000 ; WEP-64bits key1~key4 WLAN0_WEP64_KEY2=0000000000 WLAN0_WEP64_KEY3=0000000000 WLAN0_WEP64_KEY4=0000000000 WLAN0_WEP128_KEY1=00000000000000000000000000 ; WEP-128bits key1~key4 WLAN0_WEP128_KEY2=00000000000000000000000000 WLAN0_WEP128_KEY3=00000000000000000000000000 WLAN0_WEP128_KEY4=00000000000000000000000000 WLAN0_WEP_DEFAULT_KEY=0 ; default tx key id (0-3) WLAN0_WEP_KEY_TYPE=1 ; key type, 0 - ASCII, 1 - hex WLAN0_FRAG_THRESHOLD=2346 ; fragment threshold, 256-2346 WLAN0_RTS_THRESHOLD=2347 ; RTS threshold, 0 - 2347 WLAN0_BASIC_RATES=15 ; basic rate, bit0~bit11 for rate 1,2,5.5,11,6,9,12,18,24,36,48,54M WLAN0_SUPPORTED_RATES=4095 ; supported rate, bit0~bit11 for rate 1,2,5.5,11,6,9,12,18,24,36,48,54M WLAN0_BEACON_INTERVAL=100 ; beacon interval in ms(20-1024) WLAN0_PREAMBLE_TYPE=0 ; preamble type, 0 - long preamble, 1 - short preamble WLAN0_AUTH_TYPE=2 ; athentication type, 0 - open system, 1 - shared key, 2 - auto (both) WLAN0_HIDDEN_SSID=0 ; hidden ssid, 0 - disable, 1 - enable WLAN0_WLAN_DISABLED=0 ; wlan interface flag, 0 - wlan enabled, 1 - wlan disabled WLAN0_INACTIVITY_TIME=30000 ; wlan client inactivity time (in 10ms) WLAN0_RATE_ADAPTIVE_ENABLED=1 ; tx rate adaptive enable/disable, 1 - enabled, 0 - disabled WLAN0_MACAC_NUM=0 ; existing table entry number for mac access control WLAN0_MACAC_ENABLED=0 ; wlan mac access control flag, 0 - disable, 1 - enable WLAN0_DTIM_PERIOD=1 ; DTIM period WLAN0_BLOCK_RELAY=0 ; blocking packets between wireless client (relay), ; 0 - disabled, 1 - block relay, 2 - block relay but passup WLAN0_BAND=3 ; bit mask of band selection, 1-11b, 2-11g, 4-11a WLAN0_FIX_RATE=0 ; fixed data rate, 0-disable, bit0~bit11 for rate 1,2,5.5,11,6,9,12,18,24,36,48,54M MACAC_NUMMODE=0 ; operation mode, 0-AP, 1-client, 2-WDS, 3-AP+WDS WLAN0_ENCRYPT=0 ; 0 - Encrypt disabled, 1 - WEP, 2 - WPA, 4 - WPA2, 6 - WPA2 mixed WLAN0_ENABLE_1X=0 ; 802.1x flag, 0 - disabled, 1 - enabled WLAN0_WPA_AUTH=2 ; WPA authentication type, 1 - WPA-Radius, 2 - PSK WLAN0_WPA_CIPHER_SUITE=1 ; WPA Cipher suite, 1 - TKIP, 2 - AES WLAN0_WPA_PSK= ; WPA PSK value WLAN0_WPA_GROUP_REKEY_TIME=86400; group key update time (in sec) WLAN0_RS_IP=0.0.0.0 ; Radius serverIP address WLAN0_RS_PORT=1812 ; Radius server port WLAN0_RS_PASSWORD= ; Radius server password WLAN0_RS_MAXRETRY=3 ; Max retry of Radius server WLAN0_RS_INTERVAL_TIME=5 ; Interval time of retry WLAN0_WPA2_PRE_AUTH=0 ; WPA2 pre-authentication flag, 0 - disable, 1 - enable WLAN0_WPA2_CIPHER_SUITE=2 ; WPA Cipher suite, 1 - TKIP, 2 - AES WLAN0_MACCLONE_ENABLED=0 ; wlan mac clone flag (client mode used), 0 - disable, 1 - enable WLAN0_IAPP_DISABLED=0 ; IAPP flag, 0 - IAPP enabled, 1 - IAPP disabled WLAN0_PROTECTION_DISABLED=0 ; 802.11g protection mode flag, 0 - protection enable, 1 - protection disabled WLAN0_WDS_ENABLED=0 ; WDS flag, 0 - disable, 1 - enable WLAN0_WDS_NUM=0 ; existing table entry number for WDS AP WLAN0_WDS_WEP=0 ; WDS WEP flag, 0 - WEP disable, 1 - WEP-64bits, 2 - WEP-128bits, 3-TKIP, 4-AES WLAN0_WDS_WEP64_KEY1=0000000000 ; WEP-64bits key1~key4 WLAN0_WDS_WEP64_KEY2=0000000000 WLAN0_WDS_WEP64_KEY3=0000000000 WLAN0_WDS_WEP64_KEY4=0000000000 WLAN0_WDS_WEP128_KEY1=00000000000000000000000000 ; WEP-128bits key1~key4 WLAN0_WDS_WEP128_KEY2=00000000000000000000000000 WLAN0_WDS_WEP128_KEY3=00000000000000000000000000 WLAN0_WDS_WEP128_KEY4=00000000000000000000000000 WLAN0_WDS_WEP_DEFAULT_KEY=0 ; default tx key id (0-3) WLAN0_WDS_WEP_KEY_TYPE=1 ; key type, 0 - ASCII, 1 - hex WLAN0_WDS_PSK_FORMAT=0 ; psk format, 0 - ACSII, 1 - hex WLAN0_WDS_PSK= ; psk value WLAN0_EASYCFG_ENABLED=1 ; easy-config flag, 0-disable, 1-enable WLAN0_EASYCFG_MODE=1 ; easy-config mode, 1 - button, 2 - QA WLAN0_EASYCFG_ALG_REQ=32 ; request encryption (client mode), 4-TKIP, 32-AES WLAN0_EASYCFG_ALG_SUPP=36 ; support encryption (AP mode), TKIP+AES WLAN0_EASYCFG_SCAN_SSID=REALTEK_EASY_CONFIG ; SSID used by easy-config ; WLAN1 interface. Note:"WLAN1" means external wlan controller connected through PCI. ; If you do not use it, you can ignore the following setting. WLAN1_WLAN_MAC_ADDR=000000000000; clone mac address WLAN1_SSID=RTL8186-VPN-GW ; SSID WLAN1_CHANNEL=11 ; channel number WLAN1_WEP=0 ; WEP flag, 0 - WEP disable, 1 - WEP-64bits, 2 - WEP-128bits WLAN1_WEP64_KEY1=0000000000 ; WEP-64bits key1~key4 WLAN1_WEP64_KEY2=0000000000 WLAN1_WEP64_KEY3=0000000000 WLAN1_WEP64_KEY4=0000000000 WLAN1_WEP128_KEY1=00000000000000000000000000 ; WEP-128bits key1~key4 WLAN1_WEP128_KEY2=00000000000000000000000000 WLAN1_WEP128_KEY3=00000000000000000000000000 WLAN1_WEP128_KEY4=00000000000000000000000000 WLAN1_WEP_DEFAULT_KEY=0 ; default tx key id (0-3) WLAN1_WEP_KEY_TYPE=1 ; key type, 0 - ASCII, 1 - hex WLAN1_FRAG_THRESHOLD=2346 ; fragment threshold, 256-2346 WLAN1_RTS_THRESHOLD=2347 ; RTS threshold, 0 - 2347 WLAN1_BASIC_RATES=15 ; basic rate, bit0~bit11 for rate 1,2,5.5,11,6,9,12,18,24,36,48,54M WLAN1_SUPPORTED_RATES=4095 ; supported rate, bit0~bit11 for rate 1,2,5.5,11,6,9,12,18,24,36,48,54M WLAN1_BEACON_INTERVAL=100 ; beacon interval in ms(20-1024) WLAN1_PREAMBLE_TYPE=0 ; preamble type, 0 - long preamble, 1 - short preamble WLAN1_AUTH_TYPE=2 ; athentication type, 0 - open system, 1 - shared key, 2 - auto (both) WLAN1_HIDDEN_SSID=0 ; hidden ssid, 0 - disable, 1 - enable WLAN1_WLAN_DISABLED=0 ; wlan interface flag, 0 - wlan enabled, 1 - wlan disabled WLAN1_INACTIVITY_TIME=30000 ; wlan client inactivity time (in 10ms) WLAN1_RATE_ADAPTIVE_ENABLED=1 ; tx rate adaptive enable/disable, 1 - enabled, 0 - disabled WLAN1_MACAC_NUM=0 ; existing table entry number for mac access control WLAN1_MACAC_ENABLED=0 ; wlan mac access control flag, 0 - disable, 1 - enable WLAN1_DTIM_PERIOD=1 ; DTIM period WLAN1_BLOCK_RELAY=0 ; blocking packets between wireless client (relay), ; 0 - disabled, 1 - block relay, 2 - block relay but passup WLAN1_BAND=3 ; bit mask of band selection, 1-11b, 2-11g, 4-11a WLAN1_FIX_RATE=0 ; fixed data rate, 0-disable, bit0~bit11 for rate 1,2,5.5,11,6,9,12,18,24,36,48,54M MACAC_NUMMODE=0 ; operation mode, 0-AP, 1-client, 2-WDS, 3-AP+WDS WLAN1_ENCRYPT=0 ; 0 - Encrypt disabled, 1 - WEP, 2 - WPA, 4 - WPA2, 6 - WPA2 mixed WLAN1_ENABLE_1X=0 ; 802.1x flag, 0 - disabled, 1 - enabled WLAN1_WPA_AUTH=2 ; WPA authentication type, 1 - WPA-Radius, 2 - PSK WLAN1_WPA_CIPHER_SUITE=1 ; WPA Cipher suite, 1 - TKIP, 2 - AES WLAN1_WPA_PSK= ; WPA PSK value WLAN1_WPA_GROUP_REKEY_TIME=86400; group key update time (in sec) WLAN1_RS_IP=0.0.0.0 ; Radius serverIP address WLAN1_RS_PORT=1812 ; Radius server port WLAN1_RS_PASSWORD= ; Radius server password WLAN1_RS_MAXRETRY=3 ; Max retry of Radius server WLAN1_RS_INTERVAL_TIME=5 ; Interval time of retry WLAN1_WPA2_PRE_AUTH=0 ; WPA2 pre-authentication flag, 0 - disable, 1 - enable WLAN1_WPA2_CIPHER_SUITE=2 ; WPA Cipher suite, 1 - TKIP, 2 - AES WLAN1_MACCLONE_ENABLED=0 ; wlan mac clone flag (client mode used), 0 - disable, 1 - enable WLAN1_IAPP_DISABLED=0 ; IAPP flag, 0 - IAPP enabled, 1 - IAPP disabled WLAN1_PROTECTION_DISABLED=0 ; 802.11g protection mode flag, 0 - protection enable, 1 - protection disabled WLAN1_WDS_ENABLED=0 ; WDS flag, 0 - disable, 1 - enable WLAN1_WDS_NUM=0 ; existing table entry number for WDS AP WLAN1_WDS_WEP=0 ; WDS WEP flag, 0 - WEP disable, 1 - WEP-64bits, 2 - WEP-128bits, 3-TKIP, 4-AES WLAN1_WDS_WEP64_KEY1=0000000000 ; WEP-64bits key1~key4 WLAN1_WDS_WEP64_KEY2=0000000000 WLAN1_WDS_WEP64_KEY3=0000000000 WLAN1_WDS_WEP64_KEY4=0000000000 WLAN1_WDS_WEP128_KEY1=00000000000000000000000000 ; WEP-128bits key1~key4 WLAN1_WDS_WEP128_KEY2=00000000000000000000000000 WLAN1_WDS_WEP128_KEY3=00000000000000000000000000 WLAN1_WDS_WEP128_KEY4=00000000000000000000000000 WLAN1_WDS_WEP_DEFAULT_KEY=0 ; default tx key id (0-3) WLAN1_WDS_WEP_KEY_TYPE=1 ; key type, 0 - ASCII, 1 - hex WLAN1_WDS_PSK_FORMAT=0 ; psk format, 0 - ACSII, 1 - hex WLAN1_WDS_PSK= ; psk value WLAN1_EASYCFG_ENABLED=1 ; easy-config flag, 0-disable, 1-enable WLAN1_EASYCFG_MODE=1 ; easy-config mode, 1 - button, 2 - QA WLAN1_EASYCFG_ALG_REQ=32 ; request encryption (client mode), 4-TKIP, 32-AES WLAN1_EASYCFG_ALG_SUPP=36 ; support encryption (AP mode), TKIP+AES WLAN1_EASYCFG_SCAN_SSID=REALTEK_EASY_CONFIG ; SSID used by easy-config