UART1 output test ok
Uart init
mfid=000000c2 devid=00002249
Found 1 x 2M flash memory

---RealTek(RTL8186)at 2005.04.27-18:04+0800 version 1.3b [16bit](180MHz)
no sys signature at 00010000!
Jump to image start=0x80350000...
early printk enabled 
Determined physical RAM map:
 memory: 01000000 @ 00000000 (usable)
Initial ramdisk at: 0x80165000 (1792000 bytes)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram console=0 ramdisk_start=0 single
Calibrating delay loop... 179.40 BogoMIPS
Memory: 12808k/16384k available (1251k kernel code, 3576k reserved, 1868k data, 44k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
check_wait... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Serial driver version 6.02 (2003-03-12) with no serial options enabled
ttyS00 at 0x00c3 (irq = 3) is a rtl_uart1
state->flags=00000000
Realtek GPIO Driver for Flash Reload Default
block: 64 slots per queue, batch=16
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
Found 1 x 2M Byte MXIC MX29LV160AB at 0xbe000000
RTL8180/RTL8185 driver version 1.6 (2005-03-18)
8186NIC Ethernet driver v0.0.2 (Jan 30, 2004)
eth0: RTL8186-NIC at 0xbd200000, 00:01:02:03:04:05, IRQ 4
eth1: RTL8186-NIC at 0xbd300000, 04:05:06:07:08:09, IRQ 5
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 1750 blocks [1 disk] into ram disk... done.
Freeing initrd memory: 1750k freed
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 44k freed
mount /proc file system ok!
serial console detected.  Disabling virtual terminals.
init started:  BusyBox v1.00-pre8 (2005.04.28-08:46+0000) multi-call binary


BusyBox v1.00-pre8 (2005.04.28-08:46+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.

Initialize wlan0 interface
killall: syslogd: no process killed
killall: klogd: no process killed
SIOCGIFFLAGS: No such device
bridge br0 doesn't exist; can't delete it
Setup bridge...
device eth0 entered promiscuous mode
eth0:phy is 8201
SIOCDELRT: No such process
device eth1 entered promiscuous mode
eth1:phy is 8201
SIOCDELRT: No such process
device wlan0 entered promiscuous mode
SIOCDELRT: No such process
br0: port 3(wlan0) entering listening state
br0: port 2(eth1) entering listening state
br0: port 3(wlan0) entering learning state
br0: port 3(wlan0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth0) entering listening state
br0: port 2(eth1) entering learning state
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth0) entering learning state
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
SIOCDELRT: No such process
SIOCDELRT: No such process

WLAN Easy Config v1.3 (2005.01.17-11:31+0000).

IEEE 802.11f (IAPP) using interface br0 (v1.6)
Auto-Discovery (ver 1.01) 
555
556
#  


# cat /va# cat /var/log# cat /var/log/sy  me# cat /var/log/messages 
0day 00:00:11 (none) syslog.info syslogd started: BusyBox v1.00-pre8 (2005.04.28-08:46+0000)
0day 00:00:11 (none) kern.notice klogd: klogd started: BusyBox v1.00-pre8 (2005.04.28-08:46+0000)
0day 00:00:11 (none) kern.warn klogd: Linux version 2.4.18-MIPS-01.00 (root@LinuxNb) (gcc version 3.3.3) #52 き 5る 13 15:14:19 CST 2005
0day 00:00:11 (none) kern.warn klogd: early printk enabled 
0day 00:00:11 (none) kern.warn klogd: Determined physical RAM map:
0day 00:00:11 (none) kern.warn klogd:  memory: 01000000 @ 00000000 (usable)
0day 00:00:11 (none) kern.warn klogd: Initial ramdisk at: 0x80165000 (1792000 bytes)
0day 00:00:11 (none) kern.warn klogd: On node 0 totalpages: 4096
0day 00:00:11 (none) kern.warn klogd: zone(0): 4096 pages.
0day 00:00:11 (none) kern.warn klogd: zone(1): 0 pages.
0day 00:00:11 (none) kern.warn klogd: zone(2): 0 pages.
0day 00:00:11 (none) kern.warn klogd: Kernel command line: root=/dev/ram console=0 ramdisk_start=0 single
0day 00:00:11 (none) kern.warn klogd: Calibrating delay loop... 179.40 BogoMIPS
0day 00:00:11 (none) kern.warn klogd: Memory: 12808k/16384k available (1251k kernel code, 3576k reserved, 1868k data, 44k init, 0k highmem)
0day 00:00:11 (none) kern.warn klogd: Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
0day 00:00:11 (none) kern.warn klogd: Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
0day 00:00:11 (none) kern.warn klogd: Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
0day 00:00:12 (none) kern.warn klogd: Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
0day 00:00:12 (none) kern.warn klogd: Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
0day 00:00:12 (none) kern.warn klogd: check_wait... unavailable.
0day 00:00:12 (none) kern.warn klogd: POSIX conformance testing by UNIFIX
0day 00:00:12 (none) kern.info klogd: Linux NET4.0 for Linux 2.4
0day 00:00:12 (none) kern.info klogd: Based upon Swansea University Computer Society NET3.039
0day 00:00:12 (none) kern.warn klogd: Initializing RT netlink socket
0day 00:00:12 (none) kern.warn klogd: Starting kswapd
0day 00:00:12 (none) kern.info klogd: Serial driver version 6.02 (2003-03-12) with no serial options enabled
0day 00:00:12 (none) kern.info klogd: ttyS00 at 0x00c3 (irq = 3) is a rtl_uart1
0day 00:00:12 (none) kern.warn klogd: state->flags=00000000
0day 00:00:12 (none) kern.warn klogd: Realtek GPIO Driver for Flash Reload Default
0day 00:00:12 (none) kern.warn klogd: block: 64 slots per queue, batch=16
0day 00:00:12 (none) kern.warn klogd: RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
0day 00:00:12 (none) kern.notice klogd: RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
0day 00:00:12 (none) kern.notice klogd: Found 1 x 2M Byte MXIC MX29LV160AB at 0xbe000000
0day 00:00:12 (none) kern.warn klogd: RTL8180/RTL8185 driver version 1.6 (2005-03-18)
0day 00:00:12 (none) kern.info klogd: 8186NIC Ethernet driver v0.0.2 (Jan 30, 2004)
0day 00:00:12 (none) kern.info klogd: eth0: RTL8186-NIC at 0xbd200000, 00:01:02:03:04:05, IRQ 4
0day 00:00:12 (none) kern.info klogd: eth1: RTL8186-NIC at 0xbd300000, 04:05:06:07:08:09, IRQ 5
0day 00:00:12 (none) kern.info klogd: NET4: Linux TCP/IP 1.0 for NET4.0
0day 00:00:12 (none) kern.info klogd: IP Protocols: ICMP, UDP, TCP
0day 00:00:12 (none) kern.warn klogd: IP: routing cache hash table of 512 buckets, 4Kbytes
0day 00:00:12 (none) kern.warn klogd: TCP: Hash tables configured (established 1024 bind 2048)
0day 00:00:12 (none) kern.info klogd: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
0day 00:00:12 (none) kern.info klogd: NET4: Ethernet Bridge 008 for NET4.0
0day 00:00:12 (none) kern.notice klogd: RAMDISK: ext2 filesystem found at block 0
0day 00:00:12 (none) kern.notice klogd: RAMDISK: Loading 1750 blocks [1 disk] into ram disk... done.
0day 00:00:12 (none) kern.warn klogd: Freeing initrd memory: 1750k freed
0day 00:00:12 (none) kern.warn klogd: VFS: Mounted root (ext2 filesystem).
0day 00:00:12 (none) kern.warn klogd: Freeing unused kernel memory: 44k freed
0day 00:00:12 (none) kern.warn klogd: mount /proc file system ok!
0day 00:00:12 (none) kern.info klogd: device eth0 entered promiscuous mode
0day 00:00:12 (none) kern.warn klogd: eth0:phy is 8201
0day 00:00:12 (none) kern.info klogd: device eth1 entered promiscuous mode
0day 00:00:12 (none) kern.warn klogd: eth1:phy is 8201
0day 00:00:12 (none) kern.info klogd: device wlan0 entered promiscuous mode
0day 00:00:12 (none) kern.info klogd: br0: port 3(wlan0) entering listening state
0day 00:00:12 (none) kern.info klogd: br0: port 2(eth1) entering listening state
0day 00:00:12 (none) kern.info klogd: br0: port 3(wlan0) entering learning state
0day 00:00:12 (none) kern.info klogd: br0: port 3(wlan0) entering forwarding state
0day 00:00:12 (none) kern.info klogd: br0: topology change detected, propagating
0day 00:00:12 (none) kern.info klogd: br0: port 1(eth0) entering listening state
0day 00:00:12 (none) kern.info klogd: br0: port 2(eth1) entering learning state
0day 00:00:12 (none) kern.info klogd: br0: port 2(eth1) entering forwarding state
0day 00:00:12 (none) kern.info klogd: br0: topology change detected, propagating
0day 00:00:12 (none) kern.info klogd: br0: port 1(eth0) entering learning state
0day 00:00:12 (none) kern.info klogd: br0: port 1(eth0) entering forwarding state
0day 00:00:12 (none) kern.info klogd: br0: topology change detected, propagating
# # cat /var/log/messages 
0day 00:00:11 (none) syslog.info syslogd started: BusyBox v1.00-pre8 (2005.04.28-08:46+0000)
0day 00:00:11 (none) kern.notice klogd: klogd started: BusyBox v1.00-pre8 (2005.04.28-08:46+0000)
0day 00:00:11 (none) kern.warn klogd: Linux version 2.4.18-MIPS-01.00 (root@LinuxNb) (gcc version 3.3.3) #52 き 5る 13 15:14:19 CST 2005
0day 00:00:11 (none) kern.warn klogd: early printk enabled 
0day 00:00:11 (none) kern.warn klogd: Determined physical RAM map:
0day 00:00:11 (none) kern.warn klogd:  memory: 01000000 @ 00000000 (usable)
0day 00:00:11 (none) kern.warn klogd: Initial ramdisk at: 0x80165000 (1792000 bytes)
0day 00:00:11 (none) kern.warn klogd: On node 0 totalpages: 4096
0day 00:00:11 (none) kern.warn klogd: zone(0): 4096 pages.
0day 00:00:11 (none) kern.warn klogd: zone(1): 0 pages.
0day 00:00:11 (none) kern.warn klogd: zone(2): 0 pages.
0day 00:00:11 (none) kern.warn klogd: Kernel command line: root=/dev/ram console=0 ramdisk_start=0 single
0day 00:00:11 (none) kern.warn klogd: Calibrating delay loop... 179.40 BogoMIPS
0day 00:00:11 (none) kern.warn klogd: Memory: 12808k/16384k available (1251k kernel code, 3576k reserved, 1868k data, 44k init, 0k highmem)
0day 00:00:11 (none) kern.warn klogd: Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
0day 00:00:11 (none) kern.warn klogd: Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
0day 00:00:11 (none) kern.warn klogd: Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
0day 00:00:12 (none) kern.warn klogd: Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
0day 00:00:12 (none) kern.warn klogd: Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
0day 00:00:12 (none) kern.warn klogd: check_wait... unavailable.
0day 00:00:12 (none) kern.warn klogd: POSIX conformance testing by UNIFIX
0day 00:00:12 (none) kern.info klogd: Linux NET4.0 for Linux 2.4
0day 00:00:12 (none) kern.info klogd: Based upon Swansea University Computer Society NET3.039
0day 00:00:12 (none) kern.warn klogd: Initializing RT netlink socket
0day 00:00:12 (none) kern.warn klogd: Starting kswapd
0day 00:00:12 (none) kern.info klogd: Serial driver version 6.02 (2003-03-12) with no serial options enabled
0day 00:00:12 (none) kern.info klogd: ttyS00 at 0x00c3 (irq = 3) is a rtl_uart1
0day 00:00:12 (none) kern.warn klogd: state->flags=00000000
0day 00:00:12 (none) kern.warn klogd: Realtek GPIO Driver for Flash Reload Default
0day 00:00:12 (none) kern.warn klogd: block: 64 slots per queue, batch=16
0day 00:00:12 (none) kern.warn klogd: RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
0day 00:00:12 (none) kern.notice klogd: RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
0day 00:00:12 (none) kern.notice klogd: Found 1 x 2M Byte MXIC MX29LV160AB at 0xbe000000
0day 00:00:12 (none) kern.warn klogd: RTL8180/RTL8185 driver version 1.6 (2005-03-18)
0day 00:00:12 (none) kern.info klogd: 8186NIC Ethernet driver v0.0.2 (Jan 30, 2004)
0day 00:00:12 (none) kern.info klogd: eth0: RTL8186-NIC at 0xbd200000, 00:01:02:03:04:05, IRQ 4
0day 00:00:12 (none) kern.info klogd: eth1: RTL8186-NIC at 0xbd300000, 04:05:06:07:08:09, IRQ 5
0day 00:00:12 (none) kern.info klogd: NET4: Linux TCP/IP 1.0 for NET4.0
0day 00:00:12 (none) kern.info klogd: IP Protocols: ICMP, UDP, TCP
0day 00:00:12 (none) kern.warn klogd: IP: routing cache hash table of 512 buckets, 4Kbytes
0day 00:00:12 (none) kern.warn klogd: TCP: Hash tables configured (established 1024 bind 2048)
0day 00:00:12 (none) kern.info klogd: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
0day 00:00:12 (none) kern.info klogd: NET4: Ethernet Bridge 008 for NET4.0
0day 00:00:12 (none) kern.notice klogd: RAMDISK: ext2 filesystem found at block 0
0day 00:00:12 (none) kern.notice klogd: RAMDISK: Loading 1750 blocks [1 disk] into ram disk... done.
0day 00:00:12 (none) kern.warn klogd: Freeing initrd memory: 1750k freed
0day 00:00:12 (none) kern.warn klogd: VFS: Mounted root (ext2 filesystem).
0day 00:00:12 (none) kern.warn klogd: Freeing unused kernel memory: 44k freed
0day 00:00:12 (none) kern.warn klogd: mount /proc file system ok!
0day 00:00:12 (none) kern.info klogd: device eth0 entered promiscuous mode
0day 00:00:12 (none) kern.warn klogd: eth0:phy is 8201
0day 00:00:12 (none) kern.info klogd: device eth1 entered promiscuous mode
0day 00:00:12 (none) kern.warn klogd: eth1:phy is 8201
0day 00:00:12 (none) kern.info klogd: device wlan0 entered promiscuous mode
0day 00:00:12 (none) kern.info klogd: br0: port 3(wlan0) entering listening state
0day 00:00:12 (none) kern.info klogd: br0: port 2(eth1) entering listening state
0day 00:00:12 (none) kern.info klogd: br0: port 3(wlan0) entering learning state
0day 00:00:12 (none) kern.info klogd: br0: port 3(wlan0) entering forwarding state
0day 00:00:12 (none) kern.info klogd: br0: topology change detected, propagating
0day 00:00:12 (none) kern.info klogd: br0: port 1(eth0) entering listening state
0day 00:00:12 (none) kern.info klogd: br0: port 2(eth1) entering learning state
0day 00:00:12 (none) kern.info klogd: br0: port 2(eth1) entering forwarding state
0day 00:00:12 (none) kern.info klogd: br0: topology change detected, propagating
0day 00:00:12 (none) kern.info klogd: br0: port 1(eth0) entering learning state
0day 00:00:12 (none) kern.info klogd: br0: port 1(eth0) entering forwarding state
0day 00:00:12 (none) kern.info klogd: br0: topology change detected, propagating
# ls
bin         etc         lost+found  sbin        usr         web
dev         lib         proc        tmp         var
# ps
  PID  Uid     VmSize Stat Command
    1 root        248 S   init        
    2 root            SW  [keventd]
    3 root            SWN [ksoftirqd_CPU0]
    4 root            SW  [kswapd]
    5 root            SW  [bdflush]
    6 root            SW  [kupdated]
    7 root            SW  [mtdblockd]
    8 root        368 S   -sh 
  425 root        224 S   syslogd -L 
  426 root        216 S   klogd 
  503 root        220 S   autoconf -server -button -w wlan0 
  517 root        188 S   iapp br0 wlan0 
  523 root        196 S   iwcontrol wlan0 
  549 root        180 S   disc_server br0 
  555 root        324 S   webs 
  556 root        140 S   udps 
  560 root        236 R   ps 
# mount
mount: not found
# df
df: not found
# ifc# ifconfig -a
br0       Link encap:Ethernet  HWaddr 00:4F:62:03:DA:A2  
          inet addr:192.168.1.253  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:5 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:230 (230.0 B)  TX bytes:0 (0.0 B)

eth0      Link encap:Ethernet  HWaddr 00:4F:62:03:DA:A2  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:5 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100 
          RX bytes:230 (230.0 B)  TX bytes:0 (0.0 B)
          Interrupt:4 

eth1      Link encap:Ethernet  HWaddr 00:4F:62:03:DA:A3  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100 
          RX bytes:0 (0.0 B)  TX bytes:300 (300.0 B)
          Interrupt:5 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan0     Link encap:Ethernet  HWaddr 00:4F:62:03:DA:A4  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:2 

wlan0-wds Link encap:Ethernet  HWaddr 00:00:00:00:00:00  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan0-wds Link encap:Ethernet  HWaddr 00:00:00:00:00:00  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan0-wds Link encap:Ethernet  HWaddr 00:00:00:00:00:00  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan0-wds Link encap:Ethernet  HWaddr 00:00:00:00:00:00  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan0-wds Link encap:Ethernet  HWaddr 00:00:00:00:00:00  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan0-wds Link encap:Ethernet  HWaddr 00:00:00:00:00:00  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan0-wds Link encap:Ethernet  HWaddr 00:00:00:00:00:00  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan0-wds Link encap:Ethernet  HWaddr 00:00:00:00:00:00  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

# brc# brctl 
commands:
	addbr		<bridge>		add bridge
	addif		<bridge> <device>	add interface to bridge
	delbr		<bridge>		delete bridge
	delif		<bridge> <device>	delete interface from bridge
	show					show a list of bridges
	showmacs	<bridge>		show a list of mac addrs
	showstp		<bridge>		show bridge stp info

	setageing	<bridge> <time>		set ageing time
	setbridgeprio	<bridge> <prio>		set bridge priority
	setfd		<bridge> <time>		set bridge forward delay
	setgcint	<bridge> <time>		set garbage collection interval
	sethello	<bridge> <time>		set hello time
	setmaxage	<bridge> <time>		set max message age
	setpathcost	<bridge> <port> <cost>	set path cost
	setportprio	<bridge> <port> <prio>	set port priority
	stp		<bridge> <state>	turn stp on/off
# # brctl show
bridge name	bridge id		STP enabled	interfaces
br0		8000.004f6203daa2	no		eth0
							eth1
							wlan0
# ipta   # i
iapp        ifconfig    init        init.sh     iwcontrol   iwpriv 
# iwp# iwpriv 
lo        no private ioctls.

wlan0     Available private ioctl :
          set_mib          (89F1) : set 350 char  & get   0      
          get_mib          (89F2) : set  40 char  & get 128 byte 
          write_reg        (89F3) : set 128 char  & get   0      
          read_reg         (89F4) : set 128 char  & get 128 byte 
          write_mem        (89F5) : set 128 char  & get   0      
          read_mem         (89F6) : set 128 char  & get 128 byte 
          write_bb         (89FA) : set 128 char  & get   0      
          read_bb          (89FB) : set 128 char  & get 128 byte 
          write_rf         (89FC) : set 128 char  & get   0      
          read_rf          (89FD) : set 128 char  & get 128 byte 
          del_sta          (89F7) : set 128 char  & get   0      
          write_eeprom     (89F8) : set 128 char  & get   0      
          read_eeprom      (89F9) : set 128 char  & get 128 byte 
          mp_start         (8B61) : set   0       & get   0      
          mp_stop          (8B62) : set   0       & get   0      
          mp_rate          (8B63) : set  40 char  & get   0      
          mp_channel       (8B64) : set  40 char  & get   0      
          mp_txpower       (8B65) : set  40 char  & get   0      
          mp_ctx           (8B66) : set 128 char  & get   0      
          mp_arx           (8B67) : set  40 char  & get   0      
          mp_bssid         (8B68) : set  40 char  & get   0      

wlan0-wd  no private ioctls.

wlan0-wd  no private ioctls.

wlan0-wd  no private ioctls.

wlan0-wd  no private ioctls.

wlan0-wd  no private ioctls.

wlan0-wd  no private ioctls.

wlan0-wd  no private ioctls.

wlan0-wd  no private ioctls.

eth0      no private ioctls.

eth1      no private ioctls.

br0       no private ioctls.

# # iwpriv       wco# iwcontrol 
At least one wlan interface should be binded
# cd /pr      uname
uname: not found
# cd /pro# cd /proc/
# pwd
pwd: not found
# ls
1            517          bus          fs           meminfo      stat
2            549          cmdline      gpio         misc         swaps
3            555          cpuinfo      iomem        mounts       sys
4            556          devices      ioports      mtd          tty
425          570          dma          kcore        net          uptime
426          6            driver       kmsg         partitions   version
5            7            execdomains  loadavg      self         wlan0
503          8            filesystems  locks        slabinfo
# cat cm# cat cmdline 
root=/dev/ram console=0 ramdisk_start=0 single
# cat cpu# cat cpuinfo 
system type		: Philips Nino
processor		: 0
cpu model		: R3000 V0.0
BogoMIPS		: 179.40
wait instruction	: no
microsecond timers	: no
tlb_entries		: 64
extra interrupt vector	: no
hardware watchpoint	: no
VCED exceptions		: not available
VCEI exceptions		: not available
ll emulations		: 0
sc emulations		: 0
# cat de# cat devices 
Character devices:
  1 mem
  2 pty
  3 ttyp
  4 ttyS
  5 cua
 10 misc
 13 wlan/chr
162 raw

Block devices:
  1 ramdisk
 31 mtdblock
# cat dma# cat dma 
 4: cascade
# ls
1            517          bus          fs           meminfo      stat
2            549          cmdline      gpio         misc         swaps
3            555          cpuinfo      iomem        mounts       sys
4            556          devices      ioports      mtd          tty
425          575          dma          kcore        net          uptime
426          6            driver       kmsg         partitions   version
5            7            execdomains  loadavg      self         wlan0
503          8            filesystems  locks        slabinfo
# cat gpio# cat gpio 
0
# cat mem# cat meminfo 
        total:    used:    free:  shared: buffers:  cached:
Mem:  14954496  6172672  8781824        0   122880  3264512
Swap:        0        0        0
MemTotal:        14604 kB
MemFree:          8576 kB
MemShared:           0 kB
Buffers:           120 kB
Cached:           3188 kB
SwapCached:          0 kB
Active:            696 kB
Inactive:         3140 kB
HighTotal:           0 kB
HighFree:            0 kB
LowTotal:        14604 kB
LowFree:          8576 kB
SwapTotal:           0 kB
SwapFree:            0 kB
# cat mt# cat mtd 
dev:    size   erasesize  name
mtd0: 00200000 00010000 "DiskOnChip Millennium"
# cat pa# cat partitions 
major minor  #blocks  name

# ls
1            517          bus          fs           meminfo      stat
2            549          cmdline      gpio         misc         swaps
3            555          cpuinfo      iomem        mounts       sys
4            556          devices      ioports      mtd          tty
425          580          dma          kcore        net          uptime
426          6            driver       kmsg         partitions   version
5            7            execdomains  loadavg      self         wlan0
503          8            filesystems  locks        slabinfo
# cat ve# cat version 
Linux version 2.4.18-MIPS-01.00 (root@LinuxNb) (gcc version 3.3.3) #52 き 5る 13 15:14:19 CST 2005
# cd wl# cd wlan0/
# ls -als
   0 dr-xr-xr-x    2 root     0               0 Jan  1 00:02 .
   0 dr-xr-xr-x   24 root     0               0 Jan  1 00:00 ..
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 buf_info
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 cam_info
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 desc_info
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 mib_all
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 mib_auth
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 mib_bssdesc
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 mib_dkeytbl
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 mib_erp
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 mib_gkeytbl
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 mib_operation
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 mib_rf
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 mib_rsnie
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 mib_staconfig
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 mib_wds
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 sta_info
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 sta_keyinfo
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 stats
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 txdescH
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 txdescL
   0 -rw-r--r--    1 root     0               0 Jan  1 00:02 txdescN
# cat ta  stats
  Statistics...
    up_time: 2 min 35 sec 
    tx_packets:    0
    tx_bytes:      0
    tx_retrys:     0
    tx_fails:      0
    tx_drops:      1
    rx_packets:    0
    rx_bytes:      0
    rx_retrys:     0
    rx_crc_errors: 0
    rx_errors:     0
    rx_data_drops: 0
    rx_decache:    0
    beacon_ok:     1517
    beacon_er:     0
# cd 
# ls
bin         etc         lost+found  sbin        usr         web
dev         lib         proc        tmp         var
# flash all
HW_BOARD_ID=0
HW_NIC0_ADDR=004f6203daa2
HW_NIC1_ADDR=004f6203daa3
HW_WLAN0_WLAN_ADDR=004f6203daa4
HW_WLAN0_REG_DOMAIN=1
HW_WLAN0_RF_TYPE=7
HW_WLAN0_TX_POWER_CCK=0707070707070707070707070707
HW_WLAN0_TX_POWER_OFDM=0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f
HW_WLAN0_ANT_DIVERSITY=0
HW_WLAN0_TX_ANT=0
HW_WLAN0_INIT_GAIN=4
HW_WLAN0_CCA_MODE=0
HW_WLAN0_LED_TYPE=7
HW_WLAN1_WLAN_ADDR=004f6203daa5
HW_WLAN1_REG_DOMAIN=1
HW_WLAN1_RF_TYPE=7
HW_WLAN1_TX_POWER_CCK=0808080808080808080808080808
HW_WLAN1_TX_POWER_OFDM=0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e
HW_WLAN1_ANT_DIVERSITY=0
HW_WLAN1_TX_ANT=0
HW_WLAN1_INIT_GAIN=4
HW_WLAN1_CCA_MODE=0
HW_WLAN1_LED_TYPE=2
DEF_DNS1=0.0.0.0
DEF_DNS2=0.0.0.0
DEF_DNS3=0.0.0.0
DEF_DHCP_CLIENT_START=192.168.1.100
DEF_DHCP_CLIENT_END=192.168.1.200
DEF_ELAN_MAC_ADDR=000000000000
DEF_DEVICE_NAME="RTL8186"
DEF_IP_ADDR=192.168.1.253
DEF_SUBNET_MASK=255.255.255.0
DEF_DEFAULT_GATEWAY=0.0.0.0
DEF_DHCP=0
DEF_STP_ENABLED=0
DEF_SUPER_NAME="super"
DEF_SUPER_PASSWORD="super"
DEF_USER_NAME="admin"
DEF_USER_PASSWORD=""
DEF_SCRLOG_ENABLED=0
DEF_AUTODISCOVERY_ENABLED=1
DEF_OP_MODE=1
DEF_WISP_WAN_ID=0
DEF_REMOTELOG_ENABLED=0
DEF_REMOTELOG_SERVER=0.0.0.0
DEF_WLAN0_WLAN_MAC_ADDR=000000000000
DEF_WLAN0_SSID="802.11g-AP"
DEF_WLAN0_REG_DOMAIN=1
DEF_WLAN0_CHANNEL=11
DEF_WLAN0_WEP=0
DEF_WLAN0_WEP64_KEY1=0000000000
DEF_WLAN0_WEP64_KEY2=0000000000
DEF_WLAN0_WEP64_KEY3=0000000000
DEF_WLAN0_WEP64_KEY4=0000000000
DEF_WLAN0_WEP128_KEY1=00000000000000000000000000
DEF_WLAN0_WEP128_KEY2=00000000000000000000000000
DEF_WLAN0_WEP128_KEY3=00000000000000000000000000
DEF_WLAN0_WEP128_KEY4=00000000000000000000000000
DEF_WLAN0_WEP_DEFAULT_KEY=0
DEF_WLAN0_WEP_KEY_TYPE=1
DEF_WLAN0_FRAG_THRESHOLD=2346
DEF_WLAN0_SUPPORTED_RATES=4095
DEF_WLAN0_BEACON_INTERVAL=100
DEF_WLAN0_PREAMBLE_TYPE=0
DEF_WLAN0_BASIC_RATES=15
DEF_WLAN0_RTS_THRESHOLD=2347
DEF_WLAN0_AUTH_TYPE=2
DEF_WLAN0_HIDDEN_SSID=0
DEF_WLAN0_WLAN_DISABLED=0
DEF_WLAN0_INACTIVITY_TIME=30000
DEF_WLAN0_RATE_ADAPTIVE_ENABLED=1
DEF_WLAN0_DTIM_PERIOD=1
DEF_WLAN0_MODE=0
DEF_WLAN0_NETWORK_TYPE=0
DEF_WLAN0_IAPP_DISABLED=0
DEF_WLAN0_PROTECTION_DISABLED=1
DEF_WLAN0_DEFAULT_SSID=""
DEF_WLAN0_WDS_ENABLED=0
DEF_WLAN0_WDS_NUM=0
DEF_WLAN0_WDS_ENCRYPT=0
DEF_WLAN0_WDS_WEP_FORMAT=0
DEF_WLAN0_WDS_WEP_KEY=""
DEF_WLAN0_WDS_PSK_FORMAT=0
DEF_WLAN0_WDS_PSK=""
DEF_WLAN0_ENCRYPT=0
DEF_WLAN0_ENABLE_SUPP_NONWPA=0
DEF_WLAN0_SUPP_NONWPA=0
DEF_WLAN0_WPA_AUTH=2
DEF_WLAN0_WPA_CIPHER_SUITE=1
DEF_WLAN0_WPA_PSK=""
DEF_WLAN0_WPA_GROUP_REKEY_TIME=86400
DEF_WLAN0_MAC_AUTH_ENABLED=0
DEF_WLAN0_RS_IP=0.0.0.0
DEF_WLAN0_RS_PORT=1812
DEF_WLAN0_RS_PASSWORD=""
DEF_WLAN0_RS_MAXRETRY=3
DEF_WLAN0_RS_INTERVAL_TIME=5
DEF_WLAN0_ACCOUNT_RS_ENABLED=0
DEF_WLAN0_ACCOUNT_RS_IP=0.0.0.0
DEF_WLAN0_ACCOUNT_RS_PORT=0
DEF_WLAN0_ACCOUNT_RS_PASSWORD=""
DEF_WLAN0_ACCOUNT_RS_UPDATE_ENABLED=0
DEF_WLAN0_ACCOUNT_RS_UPDATE_DELAY=0
DEF_WLAN0_ACCOUNT_RS_MAXRETRY=0
DEF_WLAN0_ACCOUNT_RS_INTERVAL_TIME=0
DEF_WLAN0_ENABLE_1X=0
DEF_WLAN0_PSK_FORMAT=0
DEF_WLAN0_WPA2_PRE_AUTH=0
DEF_WLAN0_WPA2_CIPHER_SUITE=2
DEF_WLAN0_MACAC_NUM=0
DEF_WLAN0_MACAC_ENABLED=0
DEF_WLAN0_BLOCK_RELAY=0
DEF_WLAN0_MACCLONE_ENABLED=0
DEF_WLAN0_BAND=3
DEF_WLAN0_FIX_RATE=0
DEF_WLAN0_EASYCFG_ENABLED=1
DEF_WLAN0_EASYCFG_MODE=1
DEF_WLAN0_EASYCFG_SSID=""
DEF_WLAN0_EASYCFG_KEY=""
DEF_WLAN0_EASYCFG_DIGEST=""
DEF_WLAN0_EASYCFG_ALG_REQ=32
DEF_WLAN0_EASYCFG_ALG_SUPP=36
DEF_WLAN0_EASYCFG_ROLE=0
DEF_WLAN0_EASYCFG_SCAN_SSID="REALTEK_EASY_CONFIG"
DEF_WLAN0_EASYCFG_WLAN_MODE=0
DEF_WLAN1_WLAN_MAC_ADDR=000000000000
DEF_WLAN1_SSID="RTL8186-AP"
DEF_WLAN1_REG_DOMAIN=1
DEF_WLAN1_CHANNEL=11
DEF_WLAN1_WEP=0
DEF_WLAN1_WEP64_KEY1=0000000000
DEF_WLAN1_WEP64_KEY2=0000000000
DEF_WLAN1_WEP64_KEY3=0000000000
DEF_WLAN1_WEP64_KEY4=0000000000
DEF_WLAN1_WEP128_KEY1=00000000000000000000000000
DEF_WLAN1_WEP128_KEY2=00000000000000000000000000
DEF_WLAN1_WEP128_KEY3=00000000000000000000000000
DEF_WLAN1_WEP128_KEY4=00000000000000000000000000
DEF_WLAN1_WEP_DEFAULT_KEY=0
DEF_WLAN1_WEP_KEY_TYPE=1
DEF_WLAN1_FRAG_THRESHOLD=2346
DEF_WLAN1_SUPPORTED_RATES=4095
DEF_WLAN1_BEACON_INTERVAL=100
DEF_WLAN1_PREAMBLE_TYPE=0
DEF_WLAN1_BASIC_RATES=15
DEF_WLAN1_RTS_THRESHOLD=2347
DEF_WLAN1_AUTH_TYPE=2
DEF_WLAN1_HIDDEN_SSID=0
DEF_WLAN1_WLAN_DISABLED=0
DEF_WLAN1_INACTIVITY_TIME=30000
DEF_WLAN1_RATE_ADAPTIVE_ENABLED=1
DEF_WLAN1_DTIM_PERIOD=1
DEF_WLAN1_MODE=0
DEF_WLAN1_NETWORK_TYPE=0
DEF_WLAN1_IAPP_DISABLED=0
DEF_WLAN1_PROTECTION_DISABLED=0
DEF_WLAN1_DEFAULT_SSID=""
DEF_WLAN1_WDS_ENABLED=0
DEF_WLAN1_WDS_NUM=0
DEF_WLAN1_WDS_ENCRYPT=0
DEF_WLAN1_WDS_WEP_FORMAT=0
DEF_WLAN1_WDS_WEP_KEY=""
DEF_WLAN1_WDS_PSK_FORMAT=0
DEF_WLAN1_WDS_PSK=""
DEF_WLAN1_ENCRYPT=0
DEF_WLAN1_ENABLE_SUPP_NONWPA=0
DEF_WLAN1_SUPP_NONWPA=0
DEF_WLAN1_WPA_AUTH=2
DEF_WLAN1_WPA_CIPHER_SUITE=1
DEF_WLAN1_WPA_PSK=""
DEF_WLAN1_WPA_GROUP_REKEY_TIME=86400
DEF_WLAN1_MAC_AUTH_ENABLED=0
DEF_WLAN1_RS_IP=0.0.0.0
DEF_WLAN1_RS_PORT=1812
DEF_WLAN1_RS_PASSWORD=""
DEF_WLAN1_RS_MAXRETRY=3
DEF_WLAN1_RS_INTERVAL_TIME=5
DEF_WLAN1_ACCOUNT_RS_ENABLED=0
DEF_WLAN1_ACCOUNT_RS_IP=0.0.0.0
DEF_WLAN1_ACCOUNT_RS_PORT=0
DEF_WLAN1_ACCOUNT_RS_PASSWORD=""
DEF_WLAN1_ACCOUNT_RS_UPDATE_ENABLED=0
DEF_WLAN1_ACCOUNT_RS_UPDATE_DELAY=0
DEF_WLAN1_ACCOUNT_RS_MAXRETRY=0
DEF_WLAN1_ACCOUNT_RS_INTERVAL_TIME=0
DEF_WLAN1_ENABLE_1X=0
DEF_WLAN1_PSK_FORMAT=0
DEF_WLAN1_WPA2_PRE_AUTH=0
DEF_WLAN1_WPA2_CIPHER_SUITE=2
DEF_WLAN1_MACAC_NUM=0
DEF_WLAN1_MACAC_ENABLED=0
DEF_WLAN1_BLOCK_RELAY=0
DEF_WLAN1_MACCLONE_ENABLED=0
DEF_WLAN1_BAND=3
DEF_WLAN1_FIX_RATE=0
DEF_WLAN1_EASYCFG_ENABLED=1
DEF_WLAN1_EASYCFG_MODE=1
DEF_WLAN1_EASYCFG_SSID=""
DEF_WLAN1_EASYCFG_KEY=""
DEF_WLAN1_EASYCFG_DIGEST=""
DEF_WLAN1_EASYCFG_ALG_REQ=32
DEF_WLAN1_EASYCFG_ALG_SUPP=36
DEF_WLAN1_EASYCFG_ROLE=0
DEF_WLAN1_EASYCFG_SCAN_SSID="REALTEK_EASY_CONFIG"
DEF_WLAN1_EASYCFG_WLAN_MODE=0
DNS1=0.0.0.0
DNS2=0.0.0.0
DNS3=0.0.0.0
DHCP_CLIENT_START=192.168.1.100
DHCP_CLIENT_END=192.168.1.200
ELAN_MAC_ADDR=000000000000
DEVICE_NAME="RTL8186"
IP_ADDR=192.168.1.253
SUBNET_MASK=255.255.255.0
DEFAULT_GATEWAY=0.0.0.0
DHCP=0
STP_ENABLED=0
SUPER_NAME="super"
SUPER_PASSWORD="super"
USER_NAME="admin"
USER_PASSWORD=""
SCRLOG_ENABLED=3
AUTODISCOVERY_ENABLED=1
OP_MODE=1
WISP_WAN_ID=0
REMOTELOG_ENABLED=0
REMOTELOG_SERVER=0.0.0.0
WLAN0_WLAN_MAC_ADDR=000000000000
WLAN0_SSID="802.11g-AP"
WLAN0_REG_DOMAIN=1
WLAN0_CHANNEL=11
WLAN0_WEP=0
WLAN0_WEP64_KEY1=0000000000
WLAN0_WEP64_KEY2=0000000000
WLAN0_WEP64_KEY3=0000000000
WLAN0_WEP64_KEY4=0000000000
WLAN0_WEP128_KEY1=00000000000000000000000000
WLAN0_WEP128_KEY2=00000000000000000000000000
WLAN0_WEP128_KEY3=00000000000000000000000000
WLAN0_WEP128_KEY4=00000000000000000000000000
WLAN0_WEP_DEFAULT_KEY=0
WLAN0_WEP_KEY_TYPE=1
WLAN0_FRAG_THRESHOLD=2346
WLAN0_SUPPORTED_RATES=4095
WLAN0_BEACON_INTERVAL=100
WLAN0_PREAMBLE_TYPE=0
WLAN0_BASIC_RATES=15
WLAN0_RTS_THRESHOLD=2347
WLAN0_AUTH_TYPE=2
WLAN0_HIDDEN_SSID=0
WLAN0_WLAN_DISABLED=0
WLAN0_INACTIVITY_TIME=30000
WLAN0_RATE_ADAPTIVE_ENABLED=1
WLAN0_DTIM_PERIOD=1
WLAN0_MODE=0
WLAN0_NETWORK_TYPE=0
WLAN0_IAPP_DISABLED=0
WLAN0_PROTECTION_DISABLED=1
WLAN0_DEFAULT_SSID=""
WLAN0_WDS_ENABLED=0
WLAN0_WDS_NUM=0
WLAN0_WDS_ENCRYPT=0
WLAN0_WDS_WEP_FORMAT=0
WLAN0_WDS_WEP_KEY=""
WLAN0_WDS_PSK_FORMAT=0
WLAN0_WDS_PSK=""
WLAN0_ENCRYPT=0
WLAN0_ENABLE_SUPP_NONWPA=0
WLAN0_SUPP_NONWPA=0
WLAN0_WPA_AUTH=2
WLAN0_WPA_CIPHER_SUITE=1
WLAN0_WPA_PSK=""
WLAN0_WPA_GROUP_REKEY_TIME=86400
WLAN0_MAC_AUTH_ENABLED=0
WLAN0_RS_IP=0.0.0.0
WLAN0_RS_PORT=1812
WLAN0_RS_PASSWORD=""
WLAN0_RS_MAXRETRY=3
WLAN0_RS_INTERVAL_TIME=5
WLAN0_ACCOUNT_RS_ENABLED=0
WLAN0_ACCOUNT_RS_IP=0.0.0.0
WLAN0_ACCOUNT_RS_PORT=0
WLAN0_ACCOUNT_RS_PASSWORD=""
WLAN0_ACCOUNT_RS_UPDATE_ENABLED=0
WLAN0_ACCOUNT_RS_UPDATE_DELAY=0
WLAN0_ACCOUNT_RS_MAXRETRY=0
WLAN0_ACCOUNT_RS_INTERVAL_TIME=0
WLAN0_ENABLE_1X=0
WLAN0_PSK_FORMAT=0
WLAN0_WPA2_PRE_AUTH=0
WLAN0_WPA2_CIPHER_SUITE=2
WLAN0_MACAC_NUM=0
WLAN0_MACAC_ENABLED=0
WLAN0_BLOCK_RELAY=0
WLAN0_MACCLONE_ENABLED=0
WLAN0_BAND=3
WLAN0_FIX_RATE=0
WLAN0_EASYCFG_ENABLED=1
WLAN0_EASYCFG_MODE=1
WLAN0_EASYCFG_SSID=""
WLAN0_EASYCFG_KEY=""
WLAN0_EASYCFG_DIGEST=""
WLAN0_EASYCFG_ALG_REQ=32
WLAN0_EASYCFG_ALG_SUPP=36
WLAN0_EASYCFG_ROLE=0
WLAN0_EASYCFG_SCAN_SSID="REALTEK_EASY_CONFIG"
WLAN0_EASYCFG_WLAN_MODE=0
WLAN1_WLAN_MAC_ADDR=000000000000
WLAN1_SSID="RTL8186-AP"
WLAN1_REG_DOMAIN=1
WLAN1_CHANNEL=11
WLAN1_WEP=0
WLAN1_WEP64_KEY1=0000000000
WLAN1_WEP64_KEY2=0000000000
WLAN1_WEP64_KEY3=0000000000
WLAN1_WEP64_KEY4=0000000000
WLAN1_WEP128_KEY1=00000000000000000000000000
WLAN1_WEP128_KEY2=00000000000000000000000000
WLAN1_WEP128_KEY3=00000000000000000000000000
WLAN1_WEP128_KEY4=00000000000000000000000000
WLAN1_WEP_DEFAULT_KEY=0
WLAN1_WEP_KEY_TYPE=1
WLAN1_FRAG_THRESHOLD=2346
WLAN1_SUPPORTED_RATES=4095
WLAN1_BEACON_INTERVAL=100
WLAN1_PREAMBLE_TYPE=0
WLAN1_BASIC_RATES=15
WLAN1_RTS_THRESHOLD=2347
WLAN1_AUTH_TYPE=2
WLAN1_HIDDEN_SSID=0
WLAN1_WLAN_DISABLED=0
WLAN1_INACTIVITY_TIME=30000
WLAN1_RATE_ADAPTIVE_ENABLED=1
WLAN1_DTIM_PERIOD=1
WLAN1_MODE=0
WLAN1_NETWORK_TYPE=0
WLAN1_IAPP_DISABLED=0
WLAN1_PROTECTION_DISABLED=0
WLAN1_DEFAULT_SSID=""
WLAN1_WDS_ENABLED=0
WLAN1_WDS_NUM=0
WLAN1_WDS_ENCRYPT=0
WLAN1_WDS_WEP_FORMAT=0
WLAN1_WDS_WEP_KEY=""
WLAN1_WDS_PSK_FORMAT=0
WLAN1_WDS_PSK=""
WLAN1_ENCRYPT=0
WLAN1_ENABLE_SUPP_NONWPA=0
WLAN1_SUPP_NONWPA=0
WLAN1_WPA_AUTH=2
WLAN1_WPA_CIPHER_SUITE=1
WLAN1_WPA_PSK=""
WLAN1_WPA_GROUP_REKEY_TIME=86400
WLAN1_MAC_AUTH_ENABLED=0
WLAN1_RS_IP=0.0.0.0
WLAN1_RS_PORT=1812
WLAN1_RS_PASSWORD=""
WLAN1_RS_MAXRETRY=3
WLAN1_RS_INTERVAL_TIME=5
WLAN1_ACCOUNT_RS_ENABLED=0
WLAN1_ACCOUNT_RS_IP=0.0.0.0
WLAN1_ACCOUNT_RS_PORT=0
WLAN1_ACCOUNT_RS_PASSWORD=""
WLAN1_ACCOUNT_RS_UPDATE_ENABLED=0
WLAN1_ACCOUNT_RS_UPDATE_DELAY=0
WLAN1_ACCOUNT_RS_MAXRETRY=0
WLAN1_ACCOUNT_RS_INTERVAL_TIME=0
WLAN1_ENABLE_1X=0
WLAN1_PSK_FORMAT=0
WLAN1_WPA2_PRE_AUTH=0
WLAN1_WPA2_CIPHER_SUITE=2
WLAN1_MACAC_NUM=0
WLAN1_MACAC_ENABLED=0
WLAN1_BLOCK_RELAY=0
WLAN1_MACCLONE_ENABLED=0
WLAN1_BAND=3
WLAN1_FIX_RATE=0
WLAN1_EASYCFG_ENABLED=1
WLAN1_EASYCFG_MODE=1
WLAN1_EASYCFG_SSID=""
WLAN1_EASYCFG_KEY=""
WLAN1_EASYCFG_DIGEST=""
WLAN1_EASYCFG_ALG_REQ=32
WLAN1_EASYCFG_ALG_SUPP=36
WLAN1_EASYCFG_ROLE=0
WLAN1_EASYCFG_SCAN_SSID="REALTEK_EASY_CONFIG"
WLAN1_EASYCFG_WLAN_MODE=0
# flash
Usage: flash cmd
option:
cmd:
      default -- write flash parameters to default.
      get [wlan interface-index] mib-name -- get a specific mib from flash memory.
      set [wlan interface-index] mib-name mib-value -- set a specific mib into flash memory.
      all -- dump all flash parameters.
      reset -- reset current setting to default.

# flash har   all | grep HW
HW_BOARD_ID=0
HW_NIC0_ADDR=004f6203daa2
HW_NIC1_ADDR=004f6203daa3
HW_WLAN0_WLAN_ADDR=004f6203daa4
HW_WLAN0_REG_DOMAIN=1
HW_WLAN0_RF_TYPE=7
HW_WLAN0_TX_POWER_CCK=0707070707070707070707070707
HW_WLAN0_TX_POWER_OFDM=0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f
HW_WLAN0_ANT_DIVERSITY=0
HW_WLAN0_TX_ANT=0
HW_WLAN0_INIT_GAIN=4
HW_WLAN0_CCA_MODE=0
HW_WLAN0_LED_TYPE=7
HW_WLAN1_WLAN_ADDR=004f6203daa5
HW_WLAN1_REG_DOMAIN=1
HW_WLAN1_RF_TYPE=7
HW_WLAN1_TX_POWER_CCK=0808080808080808080808080808
HW_WLAN1_TX_POWER_OFDM=0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e0e
HW_WLAN1_ANT_DIVERSITY=0
HW_WLAN1_TX_ANT=0
HW_WLAN1_INIT_GAIN=4
HW_WLAN1_CCA_MODE=0
HW_WLAN1_LED_TYPE=2
# ls
bin         etc         lost+found  sbin        usr         web
dev         lib         proc        tmp         var
# cd b# cd bin/
# ls
auth         cp           fixedip.sh   iwpriv       ps           udhcpd
autoconf     dhcpc.sh     flash        kill         rm           udps
brctl        dhcpd.sh     grep         ls           sh           webs
bridge.sh    disc_server  iapp         mkdir        sleep        wlan.sh
busybox      echo         init.sh      msh          true         wlanapp.sh
cat          false        iwcontrol    ping         udhcpc
# cat bri# cat bridge.sh 
#!/bin/sh
#
# script file to start bridge
#
# Usage: bridge.sh br_interface lan1_interface wlan_interface[1]..wlan_interface[N]
#

if [ $# -lt 3 ]; then echo "Usage: $0 br_interface lan1_interface wlan_interface lan2_interface...";  exit 1 ; fi

GETMIB="flash get"
BR_UTIL=brctl
SET_IP=fixedip.sh
START_DHCP_CLIENT=dhcpc.sh
IFCONFIG=ifconfig
WLAN_PREFIX=wlan
LAN_PREFIX=eth
MAX_WDS_NUM=8

if [ "$3" != "null" ]; then	
	# shutdown LAN interface (ethernt, wlan, WDS, bridge)
	$IFCONFIG $2 down
	for ARG in $* ; do
		INTERFACE=`echo $ARG | cut -b -4`
		if [ $INTERFACE = $WLAN_PREFIX ]; then	
			$IFCONFIG $ARG down
			num=0
			while [ $num -lt $MAX_WDS_NUM ]
			do
				$IFCONFIG $ARG-wds$num down
				num=`expr $num + 1`
			done			
		fi	
	done

	$IFCONFIG $1 down
	$BR_UTIL delbr $1

	# Enable LAN interface (Ethernet, wlan, WDS, bridge)
	echo 'Setup bridge...'
	$BR_UTIL addbr $1

	eval `$GETMIB STP_ENABLED`
	if [ "$STP_ENABLED" = '0' ]; then
		$BR_UTIL setfd $1 0
		$BR_UTIL stp $1 0
	else
		$BR_UTIL setfd $1 4
		$BR_UTIL stp $1 1
	fi

	#Add lan port to bridge interface
	for ARG in $* ; do
		INTERFACE=`echo $ARG | cut -b -3`
		if [ $INTERFACE = $LAN_PREFIX ]; then	
			$BR_UTIL addif $1 $ARG
			$SET_IP $ARG  0.0.0.0
		fi	
	done
	
	for ARG in $* ; do
		INTERFACE=`echo $ARG | cut -b -4`
		if [ $INTERFACE = $WLAN_PREFIX ]; then
			eval `$GETMIB $ARG WLAN_DISABLED`	
			if [ "$WLAN_DISABLED" = 0 ]; then
				eval `$GETMIB OP_MODE`
				eval `$GETMIB WISP_WAN_ID`
				# if opmode is wireless isp, don't add wlan0 to bridge
				if [ "$OP_MODE" != '2' ] || [ $ARG != "wlan$WISP_WAN_ID" ] ;then
					$BR_UTIL addif $1 $ARG		
					$SET_IP $ARG 0.0.0.0
				else
					$IFCONFIG $ARG up
				fi		
				eval `$GETMIB $ARG WDS_ENABLED`
				eval `$GETMIB $ARG WDS_NUM`
				eval `$GETMIB $ARG MODE`
				if [ $WDS_ENABLED != 0 ] && [ $WDS_NUM != 0 ] && [ $MODE = 2 -o $MODE = 3 ]; then
					num=0
					while [ $num -lt $WDS_NUM ]
					do
						$BR_UTIL addif $1 $ARG-wds$num
						$SET_IP $ARG-wds$num 0.0.0.0		
						num=`expr $num + 1`
					done
				fi				
			fi
		fi	
	done	

	$SET_IP $1 0.0.0.0
fi

# Set fixed IP or start DHCP client
eval `$GETMIB DHCP`
if [ "$DHCP" = '0' -o "$DHCP" = '2' ]; then
	eval `$GETMIB IP_ADDR`
	eval `$GETMIB SUBNET_MASK`
	eval `$GETMIB DEFAULT_GATEWAY`
	$SET_IP $1 $IP_ADDR $SUBNET_MASK $DEFAULT_GATEWAY
elif [ "$DHCP" = '1' ]; then
  {
  	eval `$GETMIB STP_ENABLED`
	if [ "$STP_ENABLED" = '1' ]; then
		echo 'waiting for bridge initialization...'
		sleep 30
	fi
	$START_DHCP_CLIENT $1 no
  }&
fi
# cat wl# cat wlan.# cat wlan.sh 
#!/bin/sh
#
# script file to start WLAN
#
if [ $# -lt 1 ]; then echo "Usage: $0 wlan_interface";  exit 1 ; fi

GETMIB="flash get $1"
SET_WLAN="iwpriv $1"
SET_WLAN_PARAM="$SET_WLAN set_mib"
IFCONFIG=ifconfig
START_WLAN_APP=wlanapp.sh
MAX_WDS_NUM=8

## Disable WLAN MAC driver and shutdown interface first ##
$IFCONFIG $1 down

# shutdown all WDS interface
num=0
while [ $num -lt $MAX_WDS_NUM ]
do
	$IFCONFIG $1-wds$num down
	num=`expr $num + 1`
done

## kill wlan application daemon ##
$START_WLAN_APP kill $1

eval `$GETMIB HW_RF_TYPE`
eval `$GETMIB WLAN_DISABLED`
if [ "$WLAN_DISABLED" = '1' -o "$HW_RF_TYPE" = '0' ]; then
	exit 1
fi

## Set parameters to driver ##
#marked for using our Region parameter by Richard H.,2005/4/22 11:23
#eval `$GETMIB HW_REG_DOMAIN`
#$SET_WLAN_PARAM regdomain=$HW_REG_DOMAIN

eval `$GETMIB REG_DOMAIN`
$SET_WLAN_PARAM regdomain=$REG_DOMAIN

eval `$GETMIB OP_MODE`
eval `$GETMIB WLAN_MAC_ADDR`
if [ "$WLAN_MAC_ADDR" = "000000000000" ]; then
	eval `$GETMIB HW_WLAN_ADDR`
	WLAN_MAC_ADDR=$HW_WLAN_ADDR
fi
# ifconfig all wlan interface when not in WISP
# ifconfig wlan1 later interface when in WISP mode, the wlan0  will be setup in WAN interface
eval `$GETMIB WISP_WAN_ID`
if [ "$OP_MODE" != '2' ] || [ $1 != "wlan$WISP_WAN_ID" ] ;then
	$IFCONFIG $1 hw ether $WLAN_MAC_ADDR
fi

eval `$GETMIB HW_LED_TYPE`
$SET_WLAN_PARAM led_type=$HW_LED_TYPE

## set AP/client/WDS mode ##
eval `$GETMIB SSID`
$SET_WLAN_PARAM ssid="$SSID"

eval `$GETMIB MODE`
if [ "$MODE" = '1' ]; then
## client mode
	eval `$GETMIB NETWORK_TYPE`
	if  [ "$NETWORK_TYPE" = '0' ]; then
		$SET_WLAN_PARAM opmode=8
	else
		$SET_WLAN_PARAM opmode=32
		eval `$GETMIB DEFAULT_SSID`
		$SET_WLAN_PARAM defssid="$DEFAULT_SSID"
	fi
else
## AP mode
	$SET_WLAN_PARAM opmode=16
fi

if [ "$MODE" = '2' ]; then
## WDS only
	$SET_WLAN_PARAM wds_pure=1
else
	$SET_WLAN_PARAM wds_pure=0
fi

# set RF parameters
$SET_WLAN_PARAM RFChipID=$HW_RF_TYPE

eval `$GETMIB HW_ANT_DIVERSITY`
$SET_WLAN_PARAM Diversity=$HW_ANT_DIVERSITY

eval `$GETMIB HW_TX_ANT`
$SET_WLAN_PARAM DefaultAnt=$HW_TX_ANT

eval `$GETMIB HW_INIT_GAIN`
$SET_WLAN_PARAM initialGain=$HW_INIT_GAIN

#eval `$GETMIB HW_CCA_MODE`
#$SET_WLAN_PARAM CSMethod=$HW_CCA_MODE

eval `$GETMIB HW_TX_POWER_CCK`

eval `$GETMIB HW_TX_POWER_OFDM`

$SET_WLAN_PARAM TxPowerCCK=$HW_TX_POWER_CCK
$SET_WLAN_PARAM TxPowerOFDM=$HW_TX_POWER_OFDM

eval `$GETMIB BEACON_INTERVAL`
$SET_WLAN_PARAM bcnint=$BEACON_INTERVAL

eval `$GETMIB CHANNEL`
$SET_WLAN_PARAM channel=$CHANNEL

eval `$GETMIB BASIC_RATES`
$SET_WLAN_PARAM basicrates=$BASIC_RATES

eval `$GETMIB SUPPORTED_RATES`
$SET_WLAN_PARAM oprates=$SUPPORTED_RATES

eval `$GETMIB RATE_ADAPTIVE_ENABLED`
if [ "$RATE_ADAPTIVE_ENABLED" = '0' ]; then
	$SET_WLAN_PARAM autorate=0
	eval `$GETMIB FIX_RATE`
	$SET_WLAN_PARAM fixrate=$FIX_RATE
else
	$SET_WLAN_PARAM autorate=1
fi

eval `$GETMIB RTS_THRESHOLD`
$SET_WLAN_PARAM rtsthres=$RTS_THRESHOLD

eval `$GETMIB FRAG_THRESHOLD`
$SET_WLAN_PARAM fragthres=$FRAG_THRESHOLD

eval `$GETMIB INACTIVITY_TIME`
$SET_WLAN_PARAM expired_time=$INACTIVITY_TIME

eval `$GETMIB PREAMBLE_TYPE`
$SET_WLAN_PARAM preamble=$PREAMBLE_TYPE

eval `$GETMIB HIDDEN_SSID`
$SET_WLAN_PARAM hiddenAP=$HIDDEN_SSID

eval `$GETMIB DTIM_PERIOD`
$SET_WLAN_PARAM dtimperiod=$DTIM_PERIOD

$SET_WLAN_PARAM longretry=6
$SET_WLAN_PARAM shortretry=6

$SET_WLAN_PARAM aclnum=0
eval `$GETMIB MACAC_ENABLED`
$SET_WLAN_PARAM aclmode=$MACAC_ENABLED
if [ "$MACAC_ENABLED" != '0' ]; then
	eval `$GETMIB MACAC_NUM`
	if [ "$MACAC_NUM" != 0 ]; then
		num=1
		while [ $num -le $MACAC_NUM ]
		do
			AC_TBL=`$GETMIB MACAC_ADDR | grep MACAC_ADDR$num`
			addr_comment=`echo $AC_TBL | cut -f2 -d=`
			addr=`echo $addr_comment | cut -f1 -d,`
			$SET_WLAN_PARAM acladdr=$addr
			num=`expr $num + 1`
		done
	fi
fi

eval `$GETMIB AUTH_TYPE`
eval `$GETMIB ENCRYPT`
if [ "$AUTH_TYPE" = '1' ] && [ "$ENCRYPT" != '1' ]; then
	# shared-key and not WEP enabled, force to open-system
	AUTH_TYPE=0
fi
$SET_WLAN_PARAM authtype=$AUTH_TYPE

if [ "$ENCRYPT" = '0' ]; then
	$SET_WLAN_PARAM encmode=0
elif [ "$ENCRYPT" = '1' ]; then
	### WEP mode ##
	eval `$GETMIB WEP`
	if [ "$WEP" = '1' ]; then
		eval `$GETMIB WEP64_KEY1`
		eval `$GETMIB WEP64_KEY2`
		eval `$GETMIB WEP64_KEY3`
		eval `$GETMIB WEP64_KEY4`
		eval `$GETMIB WEP_DEFAULT_KEY`
		$SET_WLAN_PARAM encmode=1
		$SET_WLAN_PARAM wepkey1=$WEP64_KEY1
		$SET_WLAN_PARAM wepkey2=$WEP64_KEY2
		$SET_WLAN_PARAM wepkey3=$WEP64_KEY3
		$SET_WLAN_PARAM wepkey4=$WEP64_KEY4
		$SET_WLAN_PARAM wepdkeyid=$WEP_DEFAULT_KEY
	else
		eval `$GETMIB WEP128_KEY1`
		eval `$GETMIB WEP128_KEY2`
		eval `$GETMIB WEP128_KEY3`
		eval `$GETMIB WEP128_KEY4`
		eval `$GETMIB WEP_DEFAULT_KEY`
		$SET_WLAN_PARAM encmode=5
		$SET_WLAN_PARAM wepkey1=$WEP128_KEY1
		$SET_WLAN_PARAM wepkey2=$WEP128_KEY2
		$SET_WLAN_PARAM wepkey3=$WEP128_KEY3
		$SET_WLAN_PARAM wepkey4=$WEP128_KEY4
		$SET_WLAN_PARAM wepdkeyid=$WEP_DEFAULT_KEY
	fi
else
        ## WPA mode ##
	$SET_WLAN_PARAM encmode=2
fi

## Set 802.1x flag ##
_ENABLE_1X=0
if [ $ENCRYPT -lt 2 ]; then
	eval `$GETMIB ENABLE_1X`
	eval `$GETMIB MAC_AUTH_ENABLED`
	if [ "$ENABLE_1X" != 0 ] || [ "$MAC_AUTH_ENABLED" != 0 ]; then
		_ENABLE_1X=1
	fi
else
	_ENABLE_1X=1
fi
$SET_WLAN_PARAM 802_1x=$_ENABLE_1X

## set WDS ##
eval `$GETMIB WDS_ENABLED`
eval `$GETMIB WDS_NUM`
$SET_WLAN_PARAM wds_num=0
if [ "$MODE" = 2 -o "$MODE" = 3 ] && [ "$WDS_ENABLED" != 0 ] && [ "$WDS_NUM" != 0 ]; then
	num=1
	while [ $num -le $WDS_NUM ]
	do
		WDS_TBL=`$GETMIB WDS | grep WDS$num`
		addr_comment=`echo $WDS_TBL | cut -f2 -d=`
		addr=`echo $addr_comment | cut -f1 -d,`
		$SET_WLAN_PARAM wds_add=$addr
		num=`expr $num - 1`
		$IFCONFIG $1-wds$num hw ether $WLAN_MAC_ADDR
		num=`expr $num + 2`
	done
	$SET_WLAN_PARAM wds_enable=$WDS_ENABLED
else
	$SET_WLAN_PARAM wds_enable=0
fi

if [ "$MODE" = 2 -o "$MODE" = 3 ] && [ "$WDS_ENABLED" != '0' ]; then
	eval `$GETMIB WDS_ENCRYPT`
	if [ "$WDS_ENCRYPT" = '0' ]; then
		$SET_WLAN_PARAM wds_encrypt=0
	elif [ "$WDS_ENCRYPT" = '1' ]; then
		eval `$GETMIB WDS_WEP_KEY`
		$SET_WLAN_PARAM wds_encrypt=1
		$SET_WLAN_PARAM wds_wepkey=$WDS_WEP_KEY
	elif [ "$WDS_ENCRYPT" = '2' ]; then
		eval `$GETMIB WDS_WEP_KEY`
		$SET_WLAN_PARAM wds_encrypt=5
		$SET_WLAN_PARAM wds_wepkey=$WDS_WEP_KEY
	elif [ "$WDS_ENCRYPT" = '3' ]; then
		$SET_WLAN_PARAM wds_encrypt=2
	else
		$SET_WLAN_PARAM wds_encrypt=4
	fi
fi

# enable/disable the notification for IAPP
eval `$GETMIB IAPP_DISABLED`
if [ "$IAPP_DISABLED" = 0 ]; then
	$SET_WLAN_PARAM iapp_enable=1
else
	$SET_WLAN_PARAM iapp_enable=0
fi

#set band
eval `$GETMIB BAND`
$SET_WLAN_PARAM band=$BAND

#set nat2.5 disable when client and mac clone is set
eval `$GETMIB MACCLONE_ENABLED`
if [ "$MACCLONE_ENABLED" = '1' -a "$MODE" = '1' ]; then
	$SET_WLAN_PARAM nat25_disable=1
	$SET_WLAN_PARAM macclone_enable=1
else
	$SET_WLAN_PARAM nat25_disable=0
	$SET_WLAN_PARAM macclone_enable=0
fi
# set nat2.5 disable and macclone disable when wireless isp mode
if [ "$OP_MODE" = '2' ] ;then
	$SET_WLAN_PARAM nat25_disable=1
	$SET_WLAN_PARAM macclone_enable=0
fi

# set 11g protection mode
eval `$GETMIB PROTECTION_DISABLED`
if  [ "$PROTECTION_DISABLED" = '1' ] ;then
	$SET_WLAN_PARAM disable_protection=1
else
	$SET_WLAN_PARAM disable_protection=0
fi

# set block relay
eval `$GETMIB BLOCK_RELAY`
$SET_WLAN_PARAM block_relay=$BLOCK_RELAY

# ls
auth         cp           fixedip.sh   iwpriv       ps           udhcpd
autoconf     dhcpc.sh     flash        kill         rm           udps
brctl        dhcpd.sh     grep         ls           sh           webs
bridge.sh    disc_server  iapp         mkdir        sleep        wlan.sh
busybox      echo         init.sh      msh          true         wlanapp.sh
cat          false        iwcontrol    ping         udhcpc
# cat wl# cat wlana# cat wlanapp.sh 
#!/bin/sh
#
# script file to start wlan applications (IAPP, Auth, Autoconf) daemon
#
# Usage: wlanapp.sh [start|kill] wlan_interface...br_interface
#
if [ $# -lt 2 ] || [ $1 != 'start' -a $1 != 'kill' ] ; then
	echo "Usage: $0 [start|kill] wlan_interface...br_interface [digest] [qfirst]"
	exit 1
fi

WLAN_PREFIX=wlan
START=1
if [ $# -ge 1 ]; then
	if [ $1 = 'kill' ]; then
		START=0
	fi
	shift
fi

NAME=`echo $1 | cut -b -4`
WLAN_INTERFACE=
while [ $# -ge 1 -a "$NAME" = "$WLAN_PREFIX" ]
do
	WLAN_INTERFACE="$WLAN_INTERFACE $1"
	shift
	NAME=`echo $1 | cut -b -4`
done

if [ $START = 1 -a $# -lt 1 ]; then
	echo "Usage: $0 [start|kill] wlan_interface... bridge_interface [digest] [qfirst]"
	exit 1
fi

_GETMIB="flash get"
EASYCONF_SCRIPT=autoconf.sh
EASYCONF_DAEMON=autoconf
EASYCONF_CONFIG=/var/autoconf.conf
#DEBUG_EASYCONF=-debug
DEBUG_EASYCONF=

if [ -z "$WLAN_INTERFACE" ]; then
	echo 'Error in wlanapp.sh, no wlan interface is given!'
	exit 0
fi

## kill 802.1x, autoconf and IAPP daemon ##
PIDFILE=/var/run/iwcontrol.pid
if [ -f $PIDFILE ] ; then
       	PID=`cat $PIDFILE`
	if [ $PID != 0 ]; then
		kill -9 $PID
	fi
       	rm -f $PIDFILE
fi

for WLAN in $WLAN_INTERFACE ; do
	PIDFILE=/var/run/auth-$WLAN.pid
	if [ -f $PIDFILE ] ; then
       		PID=`cat $PIDFILE`
		if [ $PID != 0 ]; then
	       		kill -9 $PID
		fi
       		rm -f $PIDFILE
	fi

	PIDFILE=/var/run/autoconf-$WLAN.pid
	if [ -f $PIDFILE ] ; then
		$EASYCONF_DAEMON -w $WLAN -kill
		rm -f $PIDFILE
	fi
done

PIDFILE=/var/run/iapp.pid
if [ -f $PIDFILE ] ; then
       	PID=`cat $PIDFILE`
	if [ $PID != 0 ]; then
		kill -9 $PID
	fi
       	rm -f $PIDFILE
fi

rm -f /var/*.fifo

if [ $START = 0 ]; then
	exit 1
fi

## start 802.1x, autoconf and IAPP daemon ##
WLAN_ENABLED=0
IAPP_ENABLED=0
DEAMON_CREATED=0
IS_AP=0
IS_CLIENT=0

for WLAN in $WLAN_INTERFACE ; do
	GETMIB="$_GETMIB $WLAN"
	_ENABLE_1X=0
	eval `$GETMIB ENCRYPT`
	eval `$GETMIB WLAN_DISABLED`
	eval `$GETMIB MODE`
	eval `$GETMIB WDS_ENABLED`
	eval `$GETMIB WDS_NUM`

	if  [ "$WLAN_DISABLED" = 0 ] && [ "$MODE" = 2 -o "$MODE" = 3 ] &&
			[ "$WDS_ENABLED" != 0 -a "$WDS_NUM" != 0 ]; then
		eval `$GETMIB WDS_ENCRYPT`
		if [ $WDS_ENCRYPT = 3 -o $WDS_ENCRYPT = 4 ]; then
			flash wpa $WLAN /var/wpa-wds-$WLAN.conf	wds
			auth $WLAN $1 wds /var/wpa-wds-$WLAN.conf
			PIDFILE=/var/run/auth-$WLAN.pid
			while [ -f $PIDFILE ]
			do
				sleep 1
			done
		fi
	fi

	if [ "$ENCRYPT" -lt 2 ]; then
		eval `$GETMIB ENABLE_1X`
		eval `$GETMIB MAC_AUTH_ENABLED`
		if [ "$ENABLE_1X" != 0 ] || [ "$MAC_AUTH_ENABLED" != 0 ]; then
			_ENABLE_1X=1
		fi
	else
		_ENABLE_1X=1
	fi

	if [ "$_ENABLE_1X" != 0 -a "$WLAN_DISABLED" = 0 ]; then
		flash wpa $WLAN /var/wpa-$WLAN.conf
		if [ "$MODE" = '1' ]; then
			eval `$GETMIB NETWORK_TYPE`
			if [ "$NETWORK_TYPE" = '0' ]; then
				ROLE=client-infra
				#cert.sh $WLAN
			else
				ROLE=client-adhoc
			fi
		else
			ROLE=auth
		fi

		if [ "$MODE" != '2' ]; then
			auth $WLAN $1 $ROLE /var/wpa-$WLAN.conf
			DEAMON_CREATED=1
		fi
	fi


	## See if auto-config is enabled ##
	eval `$GETMIB EASYCFG_ENABLED`
	if [ "$WLAN_DISABLED" = 0 -a "$EASYCFG_ENABLED" != 0 -a "$MODE" != 2 ]; then
		## Generate autoconf config file ##
		eval `$GETMIB EASYCFG_MODE`
		eval `$GETMIB EASYCFG_ALG_REQ`
		eval `$GETMIB EASYCFG_ALG_SUPP`
		eval `$GETMIB NETWORK_TYPE`

		DO_QUESTION_REQUEST=0
		if [ $MODE = 0 -o $MODE = 3 ]; then
			eval `$GETMIB EASYCFG_DIGEST`
			echo "algorithm = $EASYCFG_ALG_SUPP" > $EASYCONF_CONFIG
		else
			echo "algorithm = $EASYCFG_ALG_REQ" > $EASYCONF_CONFIG
			if [ $NETWORK_TYPE = 0 ]; then
				if [ "$EASYCFG_MODE" = "2" -o "$EASYCFG_MODE" = "3"  ] && [ $# -lt 2 ]; then
					EASYCFG_DIGEST="00000000000000000000000000000000"
				else
					EASYCFG_DIGEST="$2"
					DO_QUESTION_REQUEST=1
				fi
			else
				if [ "$EASYCFG_MODE" = "2" -o "$EASYCFG_MODE" = "3" ] && [ $# -lt 2 ]; then
					eval `$GETMIB EASYCFG_DIGEST`
				else
					EASYCFG_DIGEST="$2"
					DO_QUESTION_REQUEST=1
				fi
			fi
		fi
		echo "digest = $EASYCFG_DIGEST" >> $EASYCONF_CONFIG

		eval `$GETMIB EASYCFG_KEY`
		echo "key = $EASYCFG_KEY" >> $EASYCONF_CONFIG

		eval `$GETMIB EASYCFG_SSID`
		echo "ssid = $EASYCFG_SSID" >> $EASYCONF_CONFIG
		echo "wlan_fifo = /var/$EASYCONF_DAEMON-$WLAN.fifo" >> $EASYCONF_CONFIG
		eval `$GETMIB EASYCFG_SCAN_SSID`
		echo "autoconf_ssid = $EASYCFG_SCAN_SSID" >> $EASYCONF_CONFIG

		## Start autoconf daemon ##
		if [ $MODE = 0 -o $MODE = 3 ]; then
			CMD="-server $DEBUG_EASYCONF"
			if [ $EASYCFG_MODE = 1 ]; then
				CMD="$CMD -button"
			elif [ $EASYCFG_MODE = 2 ]; then
				CMD="$CMD -question"
			elif [ $EASYCFG_MODE = 3 ]; then
				CMD="$CMD -button -question"
			else
				echo 'Invalid EASYCFG_MODE value !'
				exit 0
			fi
		else
			if [ $NETWORK_TYPE = 0 ]; then
				CMD="-client $DEBUG_EASYCONF"
				if [ $EASYCFG_MODE = 3 ]; then
					EASYCFG_MODE=1
				fi
			else
				CMD="-adhoc $DEBUG_EASYCONF"
			fi

			if [ "$EASYCFG_MODE" = "1" -o "$EASYCFG_MODE" = "3" ]; then
				CMD="$CMD -button"
			fi
			if [ "$EASYCFG_MODE" = "2" -o "$EASYCFG_MODE" = "3" ]; then
				if [ $# -ge 3 ] && [ "$3" = "qfirst" ]; then
					CMD="$CMD -question_first"
				else
					CMD="$CMD -question"
				fi
				if [ "$DO_QUESTION_REQUEST" = 1 ]; then
					CMD="$CMD -question_request"
				fi
			fi
		fi

		CMD="$CMD -w $WLAN"
		$EASYCONF_DAEMON $CMD
		DEAMON_CREATED=1

		if [ "$MODE" = '1' ]; then
			IS_CLIENT=1
		fi
	fi

	if [ "$EASYCFG_ENABLED" = 0 ]; then
		CMD="-w $WLAN -disable"
		$EASYCONF_DAEMON $CMD
	fi

	if [ "$WLAN_DISABLED" = 0 ]; then
		WLAN_ENABLED=1
	fi

	if [ "$MODE" = 0 -o "$MODE" = 3 ]; then
		IS_AP=1
	fi

	eval `$GETMIB IAPP_DISABLED`
	if [ $IAPP_DISABLED = 0 ]; then
		IAPP_ENABLED=1
	fi
done

# start IAPP
if [ $IAPP_ENABLED = 1 ] && [ "$WLAN_ENABLED" = 1 ] && [ "$IS_AP" = 1 ] ; then
	iapp $1 $WLAN_INTERFACE &
	DEAMON_CREATED=1
fi

if [ $IS_CLIENT = 1 ]; then
	POLL=poll
else
	POLL=
fi

if [ $DEAMON_CREATED = 1 ]; then
	iwcontrol $WLAN_INTERFACE $POLL
fi

# GPIO LED control by Richard H.
eval `$GETMIB WLAN_DISABLED`
eval `$GETMIB OP_MODE`
eval `$GETMIB ENCRYPT`
eval `$GETMIB MACAC_ENABLED`
eval `$GETMIB MODE`

#[AP]
if [ "$OP_MODE" = '1' ] && [ "$WLAN_DISABLED" = '0' ]; then
	if [ "$MODE" = '2' -o "$MODE" = '3' ]; then							#0000 0100
    	if [ "$ENCRYPT" = '0' ] && [ "$MACAC_ENABLED" = '0' ]; then		#1110 1011
    		iwpriv wlan0 write_mem dw,bd010120,1,000004EB
    	fi
    	if [ "$ENCRYPT" = '0' ] && [ "$MACAC_ENABLED" = '1' ]; then		#0110 1011
    		iwpriv wlan0 write_mem dw,bd010120,1,0000046B
    	fi
    	if [ "$ENCRYPT" != '0' ] && [ "$MACAC_ENABLED" = '0' ]; then	#1110 0011
    		iwpriv wlan0 write_mem dw,bd010120,1,000004E3
    	fi
    	if [ "$ENCRYPT" != '0' ] && [ "$MACAC_ENABLED" = '1' ]; then	#0110 0011
    		iwpriv wlan0 write_mem dw,bd010120,1,00000463
    	fi
	else																#0000 0101
		if [ "$ENCRYPT" = '0' ] && [ "$MACAC_ENABLED" = '0' ]; then		#1110 1011
    		iwpriv wlan0 write_mem dw,bd010120,1,000005EB
    	fi
    	if [ "$ENCRYPT" = '0' ] && [ "$MACAC_ENABLED" = '1' ]; then		#0110 1011
    		iwpriv wlan0 write_mem dw,bd010120,1,0000056B
    	fi
    	if [ "$ENCRYPT" != '0' ] && [ "$MACAC_ENABLED" = '0' ]; then	#1110 0011
    		iwpriv wlan0 write_mem dw,bd010120,1,000005E3
    	fi
    	if [ "$ENCRYPT" != '0' ] && [ "$MACAC_ENABLED" = '1' ]; then	#0110 0011
    		iwpriv wlan0 write_mem dw,bd010120,1,00000563
    	fi
	fi
else
	iwpriv wlan0 write_mem dw,bd010120,1,000005EB
fi

#[GW] system ready, change the power led to green
if [ "$OP_MODE" = '0' ];then
	iwpriv wlan0 write_mem dw,bd010120,1,000005e7
fi# ls
auth         cp           fixedip.sh   iwpriv       ps           udhcpd
autoconf     dhcpc.sh     flash        kill         rm           udps
brctl        dhcpd.sh     grep         ls           sh           webs
bridge.sh    disc_server  iapp         mkdir        sleep        wlan.sh
busybox      echo         init.sh      msh          true         wlanapp.sh
cat          false        iwcontrol    ping         udhcpc
# cat ini# cat init.sh 
#!/bin/sh
#
# script file to start network
#
# Usage: init.sh {gw | ap} {all | bridge | wan}
#

if [ $# -lt 2 ]; then echo "Usage: $0 {gw | ap} {all | bridge | wan}"; exit 1 ; fi

TOOL=flash
GETMIB="$TOOL get"
LOADDEF="$TOOL default"
LOADDEFSW="$TOOL default-sw"
LOADDS="$TOOL reset"
SET_IP=fixedip.sh
START_DHCP_SERVER=dhcpd.sh
START_DHCP_CLIENT=dhcpc.sh
START_BRIDGE=bridge.sh
START_WLAN=wlan.sh
START_PPPOE=pppoe.sh
START_FIREWALL=firewall.sh
START_WLAN_APP=wlanapp.sh
START_PPTP=pptp.sh
START_L2TP=l2tp.sh
START_NTP=ntp.sh
START_DDNS=ddns.sh
WLAN_PREFIX=wlan
PLUTO_PID=/var/run/pluto.pid

# Query number of wlan interface
WLAN_INTERFACE=
NUM=0

DATA=`ifconfig -a | grep $WLAN_PREFIX`
LINE=`echo $DATA | grep $WLAN_PREFIX$NUM`
NAME=`echo $LINE | cut -b -5`
while [ -n "$NAME" ]
do
	WLAN_INTERFACE="$WLAN_INTERFACE $WLAN_PREFIX$NUM"
	NUM=`expr $NUM + 1`
	LINE=`echo $DATA | grep $WLAN_PREFIX$NUM`
	NAME=`echo $LINE | cut -b -5`
done
NUM_INTERFACE=$NUM

# See if flash data is valid
$TOOL test-hwconf
if [ $? != 0 ]; then
	echo 'HW configuration invalid, reset default!'
	$LOADDEF
fi

$TOOL test-dsconf
if [ $? != 0 ]; then
	echo 'Default configuration invalid, reset default!'
	$LOADDEFSW
fi

$TOOL test-csconf
if [ $? != 0 ]; then
	echo 'Current configuration invalid, reset to default configuration!'
	$LOADDS
fi

eval `$GETMIB OP_MODE`
eval `$GETMIB WISP_WAN_ID`
if [ $1 = 'ap' ]; then
### bridge (eth0+wlan0) confiuration #########
	GATEWAY='false'
	BR_INTERFACE=br0
	BR_LAN1_INTERFACE=eth0

	#added for WA252(for second lan port) by Richard H.
	eval `$GETMIB OP_MODE`
	if [ "$OP_MODE" = '1' ];then
		BR_LAN2_INTERFACE=eth1
	fi

##############################################
fi

if [ $1 = 'gw' ]; then
### gateway (eth0+eth1+wlan0) configuration ##
	GATEWAY='true'
	if [ "$OP_MODE" = '2' ];then
		WAN_INTERFACE=wlan$WISP_WAN_ID
	else
		WAN_INTERFACE=eth1
	fi
	BR_INTERFACE=br0
	BR_LAN1_INTERFACE=eth0
	if [ "$OP_MODE" = '1' ] || [ "$OP_MODE" = '2' ]; then
		BR_LAN2_INTERFACE=eth1
	fi
##############################################
fi

if [ $2 = 'all' ]; then
	ENABLE_WAN=1
	ENABLE_BR=1
elif [ $2 = 'wan' ]; then
	ENABLE_WAN=1
	ENABLE_BR=0
elif [ $2 = 'bridge' ]; then
	# if WISP mode , restart wan for pppoe, pptp, l2tp
	if [ "$OP_MODE" = '2' ]; then
		ENABLE_WAN=1
	else
		ENABLE_WAN=0
	fi
	ENABLE_BR=1
elif [ $2 = 'wlan_app' ]; then
	$START_WLAN_APP start $WLAN_INTERFACE $BR_INTERFACE
	exit 0
else
	echo "Usage: $0 {all | bridge | wan}"; exit 1
fi



# Set Ethernet 0 MAC address
eval `$GETMIB ELAN_MAC_ADDR`
if [ "$ELAN_MAC_ADDR" = "000000000000" ]; then
	eval `$GETMIB HW_NIC0_ADDR`
	ELAN_MAC_ADDR=$HW_NIC0_ADDR
fi
ifconfig $BR_LAN1_INTERFACE hw ether $ELAN_MAC_ADDR

#set Ethernet 1 MAC Address for bridge mode and WISP
eval `$GETMIB ELAN_MAC_ADDR`
if [ "$OP_MODE" = '1' ]  || [ "$OP_MODE" = '2' ]; then
	if [ "$ELAN_MAC_ADDR" = "000000000000" ]; then
		eval `$GETMIB HW_NIC1_ADDR`
		ELAN_MAC_ADDR=$HW_NIC1_ADDR
	fi
	ifconfig $BR_LAN2_INTERFACE hw ether $ELAN_MAC_ADDR
fi

#don't setup WAN in bridge mode
if [ "$GATEWAY" = 'true' ] && [ "$OP_MODE" != '1' ] ; then
	eval `$GETMIB WAN_MAC_ADDR`
	if [ "$WAN_MAC_ADDR" = "000000000000" ]; then
		if [ "$OP_MODE" = '2' ]; then  #wireless ISP, use the WLAN mac address
			eval `$GETMIB wlan$WISP_WAN_ID HW_WLAN_ADDR`
			WAN_MAC_ADDR=$HW_WLAN_ADDR
		else
			eval `$GETMIB HW_NIC1_ADDR`
			WAN_MAC_ADDR=$HW_NIC1_ADDR
		fi
	fi
	ifconfig $WAN_INTERFACE hw ether $WAN_MAC_ADDR
fi

if [ $ENABLE_WAN = 1 -a "$GATEWAY" = 'true' ]; then  #disconnect all wan  for vpn and wisp
	# stop vpn if enabled
	if [ -f $PLUTO_PID ];then
		ipsec setup stop
	fi
	killall l2tpd
	sleep 1
	killall l2tp.sh
	killall -9 pptp.sh
	killall -9 pppoe.sh
	rm -f /etc/ppp/first*
	disconnect.sh all
fi

# Start WLAN interface
NUM=0
while [ $NUM -lt $NUM_INTERFACE -a $ENABLE_BR = 1  ]
do
	echo 'Initialize '$WLAN_PREFIX$NUM' interface'
	$START_WLAN $WLAN_PREFIX$NUM
	NUM=`expr $NUM + 1`
done

if [ "$GATEWAY" = 'true' ]; then
	if [ $ENABLE_BR = 1 ]; then
		echo 'Setup BRIDGE interface'
		PIDFILE=/etc/udhcpc/udhcpc-$BR_INTERFACE.pid
		if [ -f $PIDFILE ] ; then
			PID=`cat $PIDFILE`
			if [ $PID != 0 ]; then
				kill -9 $PID
			fi
			rm -f $PIDFILE
		fi
		#kill syslogd and klogd
		killall syslogd
		killall klogd
		#Initialize bridge interface
		$START_BRIDGE $BR_INTERFACE $BR_LAN1_INTERFACE $WLAN_INTERFACE $BR_LAN2_INTERFACE
		eval `$GETMIB SCRLOG_ENABLED`
		if [ $SCRLOG_ENABLED != 0 -a $SCRLOG_ENABLED != 2 ] ;then
			eval `$GETMIB REMOTELOG_ENABLED`
			eval `$GETMIB REMOTELOG_SERVER`
			if [ $REMOTELOG_ENABLED = "1" ] ;then
				SYSLOG_PARA="-R $REMOTELOG_SERVER"
			fi
			syslogd -L $SYSLOG_PARA &
			klogd &
		fi

		# Set fixed IP or start DHCP server
		PIDFILE=/var/run/udhcpd.pid
		if [ -f $PIDFILE ] ; then
			PID=`cat $PIDFILE`
			if [ $PID != 0 ]; then
				kill -9 $PID
	        	fi
        		rm -f $PIDFILE
		fi

		eval `$GETMIB DHCP`
		if [ "$DHCP" = '0' ]; then
			eval `$GETMIB IP_ADDR`
			eval `$GETMIB SUBNET_MASK`
			eval `$GETMIB DEFAULT_GATEWAY`
			$SET_IP $BR_INTERFACE $IP_ADDR $SUBNET_MASK $DEFAULT_GATEWAY
			$START_WLAN_APP start $WLAN_INTERFACE $BR_INTERFACE

		elif [ "$DHCP" = '2' ]; then
			# caculate wait time
			NUM=0
			WAIT_TIME=0
			while [ $NUM -lt $NUM_INTERFACE  ]
			do
				eval `$GETMIB $WLAN_PREFIX$NUM WDS_ENABLED`
				if [ "$WDS_ENABLED" != 0 ]; then
					WAIT_TIME=`expr $WAIT_TIME + 5`
				else
					WAIT_TIME=`expr $WAIT_TIME + 1`
				fi
				NUM=`expr $NUM + 1`
			done
			sleep $WAIT_TIME

			$START_DHCP_SERVER $BR_INTERFACE gw
			$START_WLAN_APP start $WLAN_INTERFACE $BR_INTERFACE
		fi
	fi

	if [ $ENABLE_WAN = 1 ]; then
		if [ "$OP_MODE" != '1' ];then
			echo 'Setup WAN interface'
		fi

		# Initialize WAN interface
		# Delete DHCP client process
		DHCPC_WAN="$WLAN_INTERFACE eth1"
		for INTF in $DHCPC_WAN ; do
			PIDFILE=/etc/udhcpc/udhcpc-$INTF.pid
			if [ -f $PIDFILE ] ; then
				PID=`cat $PIDFILE`
				if [ $PID != 0 ]; then
					kill -9 $PID
				fi
				rm -f $PIDFILE
			fi
		done

		PIDFILE=/var/run/dnrd.pid
		if [ -f $PIDFILE ] ; then
			PID=`cat $PIDFILE`
			if [ $PID != 0 ]; then
				kill -9 $PID
	        	fi
        		rm -f $PIDFILE
		fi

		eval `$GETMIB WAN_DHCP`
		if [ "$OP_MODE" != '1' ];then  # not bridge mode
                   	ifconfig $WAN_INTERFACE up
			if [ "$WAN_DHCP" = '0' ]; then
				eval `$GETMIB WAN_IP_ADDR`
				eval `$GETMIB WAN_SUBNET_MASK`
				eval `$GETMIB WAN_DEFAULT_GATEWAY`
				$SET_IP $WAN_INTERFACE $WAN_IP_ADDR $WAN_SUBNET_MASK $WAN_DEFAULT_GATEWAY

				# start DNS relay
				eval `$GETMIB DNS1`
				if [ "$DNS1" != '0.0.0.0' ]; then
					DNS="-s $DNS1"
					echo "nameserver $DNS1" > /var/resolv.conf
					cat /etc/resolv.conf
				fi
				eval `$GETMIB DNS2`
				if [ "$DNS2" != '0.0.0.0' ]; then
					DNS="$DNS -s $DNS2"
				fi
				eval `$GETMIB DNS3`
				if [ "$DNS3" != '0.0.0.0' ]; then
					DNS="$DNS -s $DNS3"
				fi
				echo start DNS Relay Daemon
				dnrd $DNS
				upnp.sh
			elif [ "$WAN_DHCP" = '1' ]; then
				$START_DHCP_CLIENT $WAN_INTERFACE wait&
				upnp.sh
			elif [ "$WAN_DHCP" = '3' ]; then
				echo 'start PPPoE daemon'
				upnp.sh
				$START_PPPOE all $WAN_INTERFACE
			elif [ "$WAN_DHCP" = '4' ]; then
				echo 'start PPTP daemon'
				upnp.sh
				$START_PPTP $WAN_INTERFACE &
			elif [ "$WAN_DHCP" = '5' ]; then
				echo 'start L2TP daemon'
                upnp.sh
                $START_L2TP $WAN_INTERFACE &
			else
				echo 'Invalid DHCP MIB value for WAN interface!'
			fi
		fi

		# enable firewall when static ip
		if [ "$WAN_DHCP" = '0' ] || [ "$OP_MODE" = '1' ]; then
			echo 'Setup Firewall'
			$START_FIREWALL
		fi
		# static ip
		if [ -f /bin/vpn.sh ] && [ "$WAN_DHCP" != '4' ] && [ "$OP_MODE" != '1' ] &&  [ "$WAN_DHCP" = '0' ] ; then
			echo 'Setup VPN'
			vpn.sh all
		fi

		#enable ntp daemon , not brige mode
		if [ "$OP_MODE" != '1' ]; then
			killall $START_NTP > /dev/null
			$START_NTP
			$START_DDNS all &
		fi

	fi

else
	# Delete DHCP server/client process
	PIDFILE=/etc/udhcpc/udhcpc-$BR_INTERFACE.pid
	if [ -f $PIDFILE ] ; then
		PID=`cat $PIDFILE`
		if [ $PID != 0 ]; then
			kill -9 $PID
	       	fi
      		rm -f $PIDFILE
	fi

	PIDFILE=/var/run/udhcpd.pid
	if [ -f $PIDFILE ] ; then
		PID=`cat $PIDFILE`
		if [ $PID != 0 ]; then
			kill -9 $PID
       		fi
      		rm -f $PIDFILE
	fi

	#kill syslogd and klogd
	killall syslogd
	killall klogd

	#added for WA252(for second lan port) by Richard H.
	eval `$GETMIB OP_MODE`
	if [ "$OP_MODE" = '1' ];then
		$START_BRIDGE $BR_INTERFACE $BR_LAN1_INTERFACE $WLAN_INTERFACE $BR_LAN2_INTERFACE
	else
		$START_BRIDGE $BR_INTERFACE $BR_LAN1_INTERFACE $WLAN_INTERFACE
	fi

	eval `$GETMIB SCRLOG_ENABLED`
	if [ $SCRLOG_ENABLED != 0 -a $SCRLOG_ENABLED != 2 ]; then
		eval `$GETMIB REMOTELOG_ENABLED`
		eval `$GETMIB REMOTELOG_SERVER`
		if [ $REMOTELOG_ENABLED = "1" ] ;then
			SYSLOG_PARA="-R $REMOTELOG_SERVER"
		fi
		syslogd -L $SYSLOG_PARA &
		klogd &
	fi

	eval `$GETMIB DHCP`
	if [ "$DHCP" = '2' ]; then
		sleep 1
		$START_DHCP_SERVER $BR_INTERFACE ap
	fi

	if [ "$DHCP" = '0' ] || [ "$DHCP" = '2' ]; then
		$START_WLAN_APP start $WLAN_INTERFACE $BR_INTERFACE
	fi
fi

# start auto-discovery daemon
PIDFILE=/var/run/disc_server.pid
if [ -f $PIDFILE ] ; then
	PID=`cat $PIDFILE`
	if [ $PID != 0 ]; then
		kill -9 $PID
	fi
	rm -f $PIDFILE
fi

eval `$GETMIB AUTODISCOVERY_ENABLED`
if [ "$AUTODISCOVERY_ENABLED" != 0 ]; then
	disc_server $BR_INTERFACE &
fi

# ls
auth         cp           fixedip.sh   iwpriv       ps           udhcpd
autoconf     dhcpc.sh     flash        kill         rm           udps
brctl        dhcpd.sh     grep         ls           sh           webs
bridge.sh    disc_server  iapp         mkdir        sleep        wlan.sh
busybox      echo         init.sh      msh          true         wlanapp.sh
cat          false        iwcontrol    ping         udhcpc
# cay t disc# cat disc_server 
ELF


@
@43�4 (4@4@4誓�@�@�
p
@
@

@@(@(@
0
4�
 @
 @
 /lib/ld-uClibc.so.0塊�@

�@	�@$0@
�@�@�
'p0Pp

pp@p
p@pp%@1*8 $
,#=;0>(+%"	-!&3<./'?45)72:96

�
��@��
�
��
�@
 ���@��
�@
@
�0
4��@L	
4��
�P��"���
4��
��29 O 
`@�@@�
P�
�c@0
(�
L
P@ �@@$0	
/@�@�
�@�

��@��@�
@��
H
(@�
�@�
!@�
�@@}@�! �@�
D@p
X@`� 
@	��@P
<$
�@@
g@0
�@ 
{@
@�
�
6@
�
I@
�
�
@
n@<t@
��,
Y@
��@
��
8�@
�_init_fini__uClibc_start_main__deregister_frame_info__register_frame_info_Jv_RegisterClasses__errno_locationstrerrorsetsockoptmemsetbindsocket_maskstrcpyioctllocal_maclocal_maskfilenamefopeninfile__fgetc_unlockedfgetcfclosedata_bufcontentheadererrinet_atonputssendtosscanfstrcmpfgetspidfilekillgetpidsprintffprintflisten_socketGetLocalInfosystemselectrecvfromgworddefileExtgword1_DYNAMIC_LINKING__RLD_MAPlibc.so.0_gp_disp_DYNAMIC_GLOBAL_OFFSET_TABLE__ftext_fdata_gp_edata__bss_start_fbss_end<�'�v���!'��牆�����
<�'�v`��!���'94 �	��
<�'�v4��!���'9#� �	�����'� 
<�'�u���!�!��'�$�
0��0 ����'������\�����< �	'�������x! �	$?����x! �	$=����x! �	$<����x! �	$:����x! �	$7����x! �	$6����x! �	$4����x! �	$3����x! �	$2����x! �	$1����x! �	$0����x! �	$.����x! �	$+����x! �	$*����x! �	$)����x! �	$'����x! �	$%����x! �	$#����x! �	$!����x! �	$ ����x! �	$����x! �	$����x! �	$���x! �	$����x! �	$����x! �	$����x! �	$<�'�s���!'��牆����$B
`�B��@'�����$B�B�C`$B���$!�"`�! �	�����$B�B�C`������@���$�4@�! �	��$
���$!
`�"���'� <�'�s��!'��牆����0�������$�4���$�
d@@�! �	�����$BH�B@���4���$�H@@�! �	�����'� <�'�rp��!'��遣�$
$$
$��@��<��8��0���� �	�����|A�"���H �	���D@�!���� �	���@0!���$�$�8$@ !4��$'�0������ �	A�����H �	���D@�!���� �	���@0!���$�$����|��4��$ '�0������ �	A�����H �	���D@�!���� �	���@0!���$�%���� �	��5!'�  !(!$���p �	�����|��$Б (!$R�$Б"��$���� �	A�����H �	���D@�!���� �	���@8!���$�%@$R����� �	Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0�����D�B4B
���D�"$
��@��8�'�H<�'�p��!'��政��(!'く�<��8���� �	�����|��'�4�'���� �	�����|��4�����@��*��+��,��
���-��.��/������� �	����<������*��+��,����
����-��.��/��������0��1����$
�'�@<�'�o��!'��惆����������$�%l����$�� �����t �	���!���P@y�"���P�c�bH@` !�e�b$�
�+@��
�f���� �	�����X �	��$=b�����P����H@����b+@�e$b
������ �	�����X �	��@(!$��b7���,$\"�!�b
$\$
b$"b�`�!&
$
b����P����H@����b+@�e$b
������ �	�����X �	��@(!$��b�����P�����d �	����$�����'�(<�'�l���!'��惆�����(!$��$���渥� ���p �	�����,(!$2���p �	�����������$�%l�!���t �	��@ !���P�"@i�!�BH@����b+@�e$b
������ �	�����X �	��@(!$��bG����$�T�0!$
$����,b���,0!�#
���,0!� ���爼&���� �	�����������L�c&
���bR�!$B
�bR��"!$Q���P�c�bH@` !�e�b$�
�+@��
�f���� �	�����X �	��$��b�����P�����d �	����$�����'�(<�'�jX��!'��政�����(!$��<��4��0��8���p �	�����l�B���L�c����&T�$�b'� ���爼0���@����
���b�d�e�������b�d�e$  !(!���p �	��$���$�%pБ '�$$R棗�"���x �	�����$�%�@���� �	�����|��$&��$x8!�������� �	A�����H �	���D@�!���� �	������|��@8!���$�%����� �	����<��4��0�'�@<�'�h���!'徐���8�栢���$�%���!���$�%鹿怪�稲�����鉛���t �	��8@�!@3�!���$�%����$�%����� �	��8<!4$
'�P��'∃��'�坏�'�惆�'∠�� '�P��$'∇��('≫��,'∵��0���� �	��8(B
@�∃$  !0BC`(!���` �	@����8'�@$�0!���� �	��8'�@'�@���$�%� 0!@��'�� !���d �	��8@!��匃冭偰佟�'�<�'�f���!'償(�� ���$�&��
亊�
政�
���!��
妙�
発�
眺�
����� �	�� ���������$�%����t �	�� @!@�!'�
�$@0! !���� �	��  !���$�&,'�
����� �	@
�� ��
�(�@$���� �	��   !���d �	�� ���� �	�� @0!'�
����$�&0���T �	�� ���������$�&4���t �	�� @�!@2$������ �	�� @0!���$�&0  !���� �	��   !���d �	�� ����$BT���爼"���8 �	�� @!�D���� �	�� @!�F'稲���$�&8 !���T �	�� �F !���$�&x���T �	��  !���� �	�� '�8 !�!$�
,� �`@��$c���|��'�($
B�s!�h0�T
@%�h$�
0!8!������ �	@
��� ���|��B�S!�B0�b0B
@��$��
�����'�
�$8!�������� �	A�� ���H �	�� �D@�!���� �	�� ����|��@8!���$�&�
����L�c<＿4B痴�d����bD���c$b|���$�&�'�
(���� �	�� ���� �	�� ���,  !���� �	�� '�
`���$�'���� �	�� ���� �	�� @ !���,���� �	�� ���L����l�4  !&���` �	@�� &2@ !���` �	@�� ���l� ���$�'8���� �	�� ���� �	�� ���,  !���� �	�� ���$�'`���� �	�� ���� �	�� @ !���,���� �	�� ���L�  !&���` �	@�� &2@ !���` �	@�� ���l� ���l�c$
b�$
`�*Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0
Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0
8! !���@���L�B�!�C$�
`(���b�����$�
$
�����$�$����$�%l���t �	�� ����@�"@ !���d �	�� ���$�'����� �	�� ���L�B�BR@���!@o�!����$BTR!'宛$E !���爼"���� �	��  !���$�'����` �	�� 'ｐ0!���$�'�&1
@8` !���$B'��B�����c�����������$B'��B�����)�������⊆���$B'��B�����∪���$B'��B��������$B'��B������$B'��B�¬���$B'��B�∃���T �	�� ���$�(���T �	�� 'ゐ���� �	�� �����B�C���L�BC!�BR$r"*@�����L�c$�bP	���l� ���� �	�w�� �`R���h �	�� ���L�c$
` !�b���@����
���b�e�f�������b�e�f(!$���p �	�� $R����$�%p'�,О(Б*���x �	@�� ���$�%����� �	�� ���|��$����$x8!�������� �	A�8�� ���H �	�� �D@�!���� �	�� ����|��@8!���$�%����� �	�!�� ���H �	�� �D@�!���� �	�� �@0!���$�(���� �	�� !��
���
���
���
���
���
�`!�'�
�<�'�\���!'��惆����$c<�c��$���渥�$�� �����&8b
$��&��`�! �	���Q��@!��$�����'�(<�'�\��!'��牆�����
<�'�[���!���'9` �	�����'� /tmp/tmpdiscover/var/run/disc_server.pidSocket create error. Errno = %d, %s
Enable broadcast error. Errno = %d (1), %s
Enable broadcast error. Errno = %d (2), %s
Bind port error. Port = %d, Errno = %d, %s
r+255.255.255.255Bad addressSendto error. Socket = %d, Errno = %d, %s
r/proc/net/routeOpen %s file error.
%16s %128s %128s %X %d %d %d %128s %d %d %dAuto-Discovery (ver 1.01) %d%d
wroute del -net 255.255.255.255 netmask 255.255.255.255 dev %sroute add -net 255.255.255.255 netmask 255.255.255.255 dev %sReceive error. Socket = %d, Errno = %d, %s
flash get USER_NAME > /tmp/tmpdiscoverflash get USER_PASSWORD > /tmp/tmpdiscoverflash get SUPER_NAME > /tmp/tmpdiscoverflash get SUPER_PASSWORD > /tmp/tmpdiscoverrm /tmp/tmpdiscoverflash get CURRENT_SUBNET_MASK%s=%d.%d.%d.%d >> /tmp/tmpdiscoverecho CURRENT_SUBNET_MASK%s >> /tmp/tmpdiscoverSelect error. Errno = %d, %s
Minicom2.00.0

Minicom2.00.0
Minicom2.00.0

Minicom2.00.0






D@$�@$�
�
����������@�@�@@
P
�@0(
L@ @@$0@@�@�
�@�@�@�
H@�@�@�@@@�@�@p@` @	�@P$@@@0@ @@
�@
�@
�
@@<@
�,@
�@
�
8@
�GCC: (GNU) 3.3.2GCC: (GNU) 3.3.3GCC: (GNU) 3.3.3GCC: (GNU) 3.3.3GCC: (GNU) 3.3.2@	������ @$0����� @��
����H@<�����@@@�����(@������(@������@@������@L�����
�@	�@$0.shstrtab.interp.reginfo.dynamic.hash.dynsym.dynstr.init.text.fini.rodata.data.rld_map.eh_frame.ctors.dtors.jcr.got.sbss.bss.comment.pdr.mdebug.abi32
@��
p@

@
 
 �%@
�
�
�+@��
3@��'
;
@	�	��A
@
@
@�G
@$0$0TM
@$�$��U
00[
000d
404n
808u
@0@|
H0H�
P0P��
818�
`1B��
1BZ
�
1�
`�
2�

2��
# Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0 Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Mi nicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Mini com2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minico m2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2 .00.0
Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0: cannot execute
# Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0 Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Mi nicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Mini com2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minico m2.00.0Minicom2.00.0Minicom2.00.0
Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0Minicom2.00.0: cannot execute
# Minicom2.00.0
Minicom2.00.0: not found
# 
# Minicom2.00.0
Minicom2.00.0: not found
# Minicom2.00.0
Minicom2.00.0: not found
# 
# Minicom2.00.0
Minicom2.00.0: not found
# 
# 
# 
# 
# 
# 
# Minicom2.00.0Minicom2.00.0
Minicom2.00.0Minicom2.00.0: not found
# 
# 
# 
# 
# 
# 
# 
# 
# 
# 
# 
# reset
reset: not found
# ls
auth         cp           fixedip.sh   iwpriv       ps           udhcpd
autoconf     dhcpc.sh     flash        kill         rm           udps
brctl        dhcpd.sh     grep         ls           sh           webs
bridge.sh    disc_server  iapp         mkdir        sleep        wlan.sh
busybox      echo         init.sh      msh          true         wlanapp.sh
cat          false        iwcontrol    ping         udhcpc
# cat dh# cat dhcpc# cat dhcpc.sh 
#!/bin/sh
#
# script file to start dhcp client (udhcpc)
#


if [ $# -lt 2 ]; then echo "Usage: $0 interface {wait|no]";  exit 1 ; fi

GETMIB="flash get"
SCRIPTFILE_PATH=/usr/share/udhcpc
PIDFILE=/etc/udhcpc/udhcpc-$1.pid
CMD="-i $1 -p $PIDFILE -s $SCRIPTFILE_PATH/$1.sh"

if [ $2 = 'no' ]; then
# marked Auto-AP
#	CMD="$CMD -n -a"
	CMD="$CMD -n"
	eval `$GETMIB IP_ADDR`
	eval `$GETMIB SUBNET_MASK`
	eval `$GETMIB DEFAULT_GATEWAY`

	# Generate deconfig script, used when DHCP request is failed

	echo "#!/bin/sh" > $SCRIPTFILE_PATH/$1.deconfig
	echo "ifconfig $1 $IP_ADDR netmask $SUBNET_MASK" >> $SCRIPTFILE_PATH/$1.deconfig
        echo "while route del default dev $1" >> $SCRIPTFILE_PATH/$1.deconfig
        echo "do :" >> $SCRIPTFILE_PATH/$1.deconfig
        echo "done" >> $SCRIPTFILE_PATH/$1.deconfig
	echo "route add -net default gw $DEFAULT_GATEWAY dev $1" >> $SCRIPTFILE_PATH/$1.deconfig

	# added to start wlan application daemon
	echo "init.sh ap wlan_app" >> $SCRIPTFILE_PATH/$1.deconfig
else
	# Generate deconfig script
	echo "#!/bin/sh" > $SCRIPTFILE_PATH/$1.deconfig
	echo "ifconfig $1 0.0.0.0" >> $SCRIPTFILE_PATH/$1.deconfig
fi

if [ -f $PIDFILE ] ; then
	PID=`cat $PIDFILE`
	if [ $PID != 0 ]; then
		kill -9 $PID
       	fi
	rm -f $PIDFILE
fi

udhcpc $CMD
# # cat dhcpc.sh      d# cat dhcpd.sh 
#!/bin/sh
#
# script file to start udhcpd daemon (udhcp server)
#

if [ $# -lt 2 ]; then echo "Usage: $0 interface {gw | ap} ";  exit 1 ; fi

GETMIB="flash get"
CONF_FILE=/var/udhcpd.conf
LEASE_FILE=/var/lib/misc/udhcpd.leases

# See if DHCP server is on
eval `$GETMIB DHCP`
if [ "$DHCP" != '2' ]; then
	exit 0
fi

echo "interface $1" > $CONF_FILE

eval `$GETMIB DHCP_CLIENT_START`
echo "start $DHCP_CLIENT_START" >> $CONF_FILE

eval `$GETMIB DHCP_CLIENT_END`
echo "end $DHCP_CLIENT_END" >> $CONF_FILE

eval `$GETMIB SUBNET_MASK`
echo "opt subnet $SUBNET_MASK" >> $CONF_FILE

if [ $2 = "ap" ]; then
	eval `$GETMIB DEFAULT_GATEWAY`
	echo "opt router $DEFAULT_GATEWAY"  >> $CONF_FILE

	eval `$GETMIB DNS1`
	if [ "$DNS1" != "0.0.0.0" ]; then
		echo "opt dns $DNS1" >> $CONF_FILE
	fi
	eval `$GETMIB DNS2`
	if [ "$DNS2" != "0.0.0.0" ]; then
		echo "opt dns $DNS2" >> $CONF_FILE
	fi
	eval `$GETMIB DNS3`
	if [ "$DNS3" != "0.0.0.0" ]; then
		echo "opt dns $DNS3" >> $CONF_FILE
	fi
	# set default
	if [ "`cat $CONF_FILE | grep dns`" = "" ]; then
		echo "opt dns $DEFAULT_GATEWAY"  >> $CONF_FILE
	fi

else
	eval `$GETMIB IP_ADDR`
	echo "opt router $IP_ADDR"  >> $CONF_FILE

	eval `$GETMIB DNS_MODE`
	if [ "$DNS_MODE" = '0' ]; then
		echo "opt dns $IP_ADDR" >> $CONF_FILE
	else
		eval `$GETMIB DNS1`
		if [ "$DNS1" != "0.0.0.0" ]; then
			echo "opt dns $DNS1" >> $CONF_FILE
		fi
		eval `$GETMIB DNS2`
		if [ "$DNS2" != "0.0.0.0" ]; then
			echo "opt dns $DNS2" >> $CONF_FILE
		fi
		eval `$GETMIB DNS3`
		if [ "$DNS3" != "0.0.0.0" ]; then
			echo "opt dns $DNS3" >> $CONF_FILE
		fi
	fi
	# set default
	if [ "`cat $CONF_FILE | grep dns`" = "" ]; then
		echo "opt dns $IP_ADDR"  >> $CONF_FILE
	fi

fi

if [ -f "$LEASE_FILE" ]; then
	rm -f $LEASE_FILE
fi

echo "" > $LEASE_FILE

eval `$GETMIB IP_ADDR`
fixedip.sh $1 $IP_ADDR $SUBNET_MASK 0.0.0.0

udhcpd $CONF_FILE






# ls
auth         cp           fixedip.sh   iwpriv       ps           udhcpd
autoconf     dhcpc.sh     flash        kill         rm           udps
brctl        dhcpd.sh     grep         ls           sh           webs
bridge.sh    disc_server  iapp         mkdir        sleep        wlan.sh
busybox      echo         init.sh      msh          true         wlanapp.sh
cat          false        iwcontrol    ping         udhcpc
# cd ..
# cd sb# cd sbin/
# ls
ifconfig  init      klogd     reboot    route     syslogd
# cd ..
# ls
bin         etc         lost+found  sbin        usr         web
dev         lib         proc        tmp         var
# cd w# cd web/
# s ; ls -als
   3 drw-------    2 root     0            3072 Jan  1 00:00 .
   1 drwxr-xr-x   13 root     0            1024 Jan  1 00:00 ..
   1 ----------    1 root     0             413 Jan  1 00:00 000line.gif
   1 ----------    1 root     0             102 Jan  1 00:00 001line.gif
   1 ----------    1 root     0             140 Jan  1 00:00 01.css
   1 ----------    1 root     0             138 Jan  1 00:00 02.css
   1 ----------    1 root     0              85 Jan  1 00:00 669898.gif
   1 ----------    1 root     0             432 Jan  1 00:00 AP_DHCP.asp
   4 ----------    1 root     0            3762 Jan  1 00:00 AP_DHCP_content.asp
   1 ----------    1 root     0             473 Jan  1 00:00 AP_DHCP_intro.asp
   1 ----------    1 root     0             634 Jan  1 00:00 AccessPoint_white.gif
   1 ----------    1 root     0             453 Jan  1 00:00 LANsetting.asp
  10 ----------    1 root     0            9338 Jan  1 00:00 LANsetting_content.asp
   1 ----------    1 root     0             611 Jan  1 00:00 LANsetting_intro.asp
   1 ----------    1 root     0             464 Jan  1 00:00 Other_00.gif
   1 ----------    1 root     0             464 Jan  1 00:00 Other_01.gif
   1 ----------    1 root     0             430 Jan  1 00:00 Password.asp
   4 ----------    1 root     0            3924 Jan  1 00:00 Password_content.asp
   1 ----------    1 root     0             433 Jan  1 00:00 Password_intro.asp
   1 ----------    1 root     0             418 Jan  1 00:00 SNMP.asp
  16 ----------    1 root     0           14658 Jan  1 00:00 SNMP_content.asp
   1 ----------    1 root     0             488 Jan  1 00:00 SNMP_intro.asp
   1 ----------    1 root     0             428 Jan  1 00:00 Save.asp
   3 ----------    1 root     0            3035 Jan  1 00:00 Save_content.asp
   1 ----------    1 root     0             513 Jan  1 00:00 Save_intro.asp
   1 ----------    1 root     0             426 Jan  1 00:00 Syslog.asp
   1 ----------    1 root     0             846 Jan  1 00:00 System.asp
   1 ----------    1 root     0             466 Jan  1 00:00 TCPIP_00.gif
   1 ----------    1 root     0             466 Jan  1 00:00 TCPIP_01.gif
   6 ----------    1 root     0            5818 Jan  1 00:00 Top1.asp
  14 ----------    1 root     0           12757 Jan  1 00:00 Top_device.gif
   1 ----------    1 root     0             442 Jan  1 00:00 Upgrafirmware.asp
   3 ----------    1 root     0            2994 Jan  1 00:00 Upgrafirmware_content.asp
   1 ----------    1 root     0             534 Jan  1 00:00 Upgrafrimware_intro.asp
   5 ----------    1 root     0            4836 Jan  1 00:00 WLANtitle.gif
   1 ----------    1 root     0             441 Jan  1 00:00 WLacsctrl.asp
   7 ----------    1 root     0            6638 Jan  1 00:00 WLacsctrl_content.asp
   1 ----------    1 root     0             689 Jan  1 00:00 WLacsctrl_intro.asp
   1 ----------    1 root     0             450 Jan  1 00:00 WLadvsetting.asp
  14 ----------    1 root     0           13283 Jan  1 00:00 WLadvsetting_content.asp
   1 ----------    1 root     0             604 Jan  1 00:00 WLadvsetting_intro.asp
   1 ----------    1 root     0             437 Jan  1 00:00 WLbasic.asp
  23 ----------    1 root     0           21948 Jan  1 00:00 WLbasic_content.asp
   1 ----------    1 root     0             587 Jan  1 00:00 WLbasic_intro.asp
   1 ----------    1 root     0             443 Jan  1 00:00 WLsecurity.asp
  24 ----------    1 root     0           23098 Jan  1 00:00 WLsecurity_content.asp
   1 ----------    1 root     0             576 Jan  1 00:00 WLsecurity_intro.asp
   1 ----------    1 root     0             574 Jan  1 00:00 Wireless_00.gif
   1 ----------    1 root     0             574 Jan  1 00:00 Wireless_01.gif
   1 ----------    1 root     0             431 Jan  1 00:00 Wrdirect.asp
   6 ----------    1 root     0            5863 Jan  1 00:00 Wrdirect_content.asp
   1 ----------    1 root     0             629 Jan  1 00:00 Wrdirect_intro.asp
   1 ----------    1 root     0             436 Jan  1 00:00 activeclient.asp
   2 ----------    1 root     0            1881 Jan  1 00:00 activeclient_content.asp
   1 ----------    1 root     0             479 Jan  1 00:00 activeclient_intro.asp
  27 ----------    1 root     0           26195 Jan  1 00:00 common.js
   3 -rwS--s---    1 root     0            2947 Jan  1 00:00 config.dat
   2 ----------    1 root     0            1734 Jan  1 00:00 dhcptbl.asp
   1 ----------    1 root     0             388 Jan  1 00:00 home.asp
   1 ----------    1 root     0             801 Jan  1 00:00 homemain.asp
   1 ----------    1 root     0             425 Jan  1 00:00 reboot.asp
   2 ----------    1 root     0            1573 Jan  1 00:00 reboot_content.asp
   1 ----------    1 root     0             390 Jan  1 00:00 reboot_intro.asp
   1 ----------    1 root     0             501 Jan  1 00:00 statistic_intro.asp
   1 ----------    1 root     0             429 Jan  1 00:00 statistics.asp
   3 ----------    1 root     0            2528 Jan  1 00:00 statistics_content.asp
   1 ----------    1 root     0             550 Jan  1 00:00 statistics_intro.asp
   1 ----------    1 root     0             489 Jan  1 00:00 status_00.gif
   1 ----------    1 root     0             489 Jan  1 00:00 status_01.gif
   1 ----------    1 root     0             422 Jan  1 00:00 survey.asp
   3 ----------    1 root     0            2639 Jan  1 00:00 survey_content.asp
   1 ----------    1 root     0             558 Jan  1 00:00 survey_intro.asp
   6 ----------    1 root     0            5734 Jan  1 00:00 syslog_content.asp
   1 ----------    1 root     0             349 Jan  1 00:00 syslog_intro.asp
   7 ----------    1 root     0            6715 Jan  1 00:00 system_content.asp
   1 ----------    1 root     0             391 Jan  1 00:00 system_intro.asp
   1 ----------    1 root     0             416 Jan  1 00:00 wds.asp
   8 ----------    1 root     0            7349 Jan  1 00:00 wds_content.asp
   1 ----------    1 root     0             674 Jan  1 00:00 wds_intro.asp
   1 ----------    1 root     0             434 Jan  1 00:00 wlautocfg.asp
  18 ----------    1 root     0           17032 Jan  1 00:00 wlautocfg_content.asp
   1 ----------    1 root     0             593 Jan  1 00:00 wlautocfg_intro.asp
   8 ----------    1 root     0            7869 Jan  1 00:00 wlwdsenp.asp
   2 ----------    1 root     0            1511 Jan  1 00:00 wlwdstbl.asp
  10 ----------    1 root     0           10083 Jan  1 00:00 wlwep.asp
# cd ..
# ls
bin         etc         lost+found  sbin        usr         web
dev         lib         proc        tmp         var
# cd b# cd bin/    e# cd etc/
# ls -akls   ls
   1 drwxr-xr-x    3 root     0            1024 May 13  2005 .
   1 drwxr-xr-x   13 root     0            1024 Jan  1 00:00 ..
   1 -rwxrwxr-x    1 500      500            17 Mar  2  2005 host.conf
   1 -rwxrwxr-x    1 500      500            50 Mar  2  2005 hosts
   1 -rwxrwxr-x    1 500      500           316 Mar  2  2005 nsswitch.conf
   1 -rwxrwxr-x    1 500      500            64 Mar  2  2005 passwd
   1 -rwxrwxr-x    1 500      500           139 Mar 31  2005 profile
   6 -rwxrwxr-x    1 500      500          5552 Mar  2  2005 protocols
   0 lrwxrwxrwx    1 root     0              16 May 13  2005 resolv.conf -> /var/resolv.conf
  19 -rwxrwxr-x    1 500      500         18105 Mar  2  2005 services
   1 drwxr-xr-x    2 root     0            1024 May 13  2005 udhcpc
# cat pa# cat passwd 
root:abSQTPcIskFGc:0:0:root:/:/bin/sh
nobody:x:99:99:Nobody:/:

# cat pr# cat prof# cat profile 
ifconfig lo   127.0.0.1

init.sh ap all

##  extact web pages ##
flash extr /web


## start web server ##
webs&

# start udp server
udps &
# cd ..
# cd b# cd bin/
# ls
auth         cp           fixedip.sh   iwpriv       ps           udhcpd
autoconf     dhcpc.sh     flash        kill         rm           udps
brctl        dhcpd.sh     grep         ls           sh           webs
bridge.sh    disc_server  iapp         mkdir        sleep        wlan.sh
busybox      echo         init.sh      msh          true         wlanapp.sh
cat          false        iwcontrol    ping         udhcpc
# cat ini# cat init.sh 
#!/bin/sh
#
# script file to start network
#
# Usage: init.sh {gw | ap} {all | bridge | wan}
#

if [ $# -lt 2 ]; then echo "Usage: $0 {gw | ap} {all | bridge | wan}"; exit 1 ; fi

TOOL=flash
GETMIB="$TOOL get"
LOADDEF="$TOOL default"
LOADDEFSW="$TOOL default-sw"
LOADDS="$TOOL reset"
SET_IP=fixedip.sh
START_DHCP_SERVER=dhcpd.sh
START_DHCP_CLIENT=dhcpc.sh
START_BRIDGE=bridge.sh
START_WLAN=wlan.sh
START_PPPOE=pppoe.sh
START_FIREWALL=firewall.sh
START_WLAN_APP=wlanapp.sh
START_PPTP=pptp.sh
START_L2TP=l2tp.sh
START_NTP=ntp.sh
START_DDNS=ddns.sh
WLAN_PREFIX=wlan
PLUTO_PID=/var/run/pluto.pid

# Query number of wlan interface
WLAN_INTERFACE=
NUM=0

DATA=`ifconfig -a | grep $WLAN_PREFIX`
LINE=`echo $DATA | grep $WLAN_PREFIX$NUM`
NAME=`echo $LINE | cut -b -5`
while [ -n "$NAME" ]
do
	WLAN_INTERFACE="$WLAN_INTERFACE $WLAN_PREFIX$NUM"
	NUM=`expr $NUM + 1`
	LINE=`echo $DATA | grep $WLAN_PREFIX$NUM`
	NAME=`echo $LINE | cut -b -5`
done
NUM_INTERFACE=$NUM

# See if flash data is valid
$TOOL test-hwconf
if [ $? != 0 ]; then
	echo 'HW configuration invalid, reset default!'
	$LOADDEF
fi

$TOOL test-dsconf
if [ $? != 0 ]; then
	echo 'Default configuration invalid, reset default!'
	$LOADDEFSW
fi

$TOOL test-csconf
if [ $? != 0 ]; then
	echo 'Current configuration invalid, reset to default configuration!'
	$LOADDS
fi

eval `$GETMIB OP_MODE`
eval `$GETMIB WISP_WAN_ID`
if [ $1 = 'ap' ]; then
### bridge (eth0+wlan0) confiuration #########
	GATEWAY='false'
	BR_INTERFACE=br0
	BR_LAN1_INTERFACE=eth0

	#added for WA252(for second lan port) by Richard H.
	eval `$GETMIB OP_MODE`
	if [ "$OP_MODE" = '1' ];then
		BR_LAN2_INTERFACE=eth1
	fi

##############################################
fi

if [ $1 = 'gw' ]; then
### gateway (eth0+eth1+wlan0) configuration ##
	GATEWAY='true'
	if [ "$OP_MODE" = '2' ];then
		WAN_INTERFACE=wlan$WISP_WAN_ID
	else
		WAN_INTERFACE=eth1
	fi
	BR_INTERFACE=br0
	BR_LAN1_INTERFACE=eth0
	if [ "$OP_MODE" = '1' ] || [ "$OP_MODE" = '2' ]; then
		BR_LAN2_INTERFACE=eth1
	fi
##############################################
fi

if [ $2 = 'all' ]; then
	ENABLE_WAN=1
	ENABLE_BR=1
elif [ $2 = 'wan' ]; then
	ENABLE_WAN=1
	ENABLE_BR=0
elif [ $2 = 'bridge' ]; then
	# if WISP mode , restart wan for pppoe, pptp, l2tp
	if [ "$OP_MODE" = '2' ]; then
		ENABLE_WAN=1
	else
		ENABLE_WAN=0
	fi
	ENABLE_BR=1
elif [ $2 = 'wlan_app' ]; then
	$START_WLAN_APP start $WLAN_INTERFACE $BR_INTERFACE
	exit 0
else
	echo "Usage: $0 {all | bridge | wan}"; exit 1
fi



# Set Ethernet 0 MAC address
eval `$GETMIB ELAN_MAC_ADDR`
if [ "$ELAN_MAC_ADDR" = "000000000000" ]; then
	eval `$GETMIB HW_NIC0_ADDR`
	ELAN_MAC_ADDR=$HW_NIC0_ADDR
fi
ifconfig $BR_LAN1_INTERFACE hw ether $ELAN_MAC_ADDR

#set Ethernet 1 MAC Address for bridge mode and WISP
eval `$GETMIB ELAN_MAC_ADDR`
if [ "$OP_MODE" = '1' ]  || [ "$OP_MODE" = '2' ]; then
	if [ "$ELAN_MAC_ADDR" = "000000000000" ]; then
		eval `$GETMIB HW_NIC1_ADDR`
		ELAN_MAC_ADDR=$HW_NIC1_ADDR
	fi
	ifconfig $BR_LAN2_INTERFACE hw ether $ELAN_MAC_ADDR
fi

#don't setup WAN in bridge mode
if [ "$GATEWAY" = 'true' ] && [ "$OP_MODE" != '1' ] ; then
	eval `$GETMIB WAN_MAC_ADDR`
	if [ "$WAN_MAC_ADDR" = "000000000000" ]; then
		if [ "$OP_MODE" = '2' ]; then  #wireless ISP, use the WLAN mac address
			eval `$GETMIB wlan$WISP_WAN_ID HW_WLAN_ADDR`
			WAN_MAC_ADDR=$HW_WLAN_ADDR
		else
			eval `$GETMIB HW_NIC1_ADDR`
			WAN_MAC_ADDR=$HW_NIC1_ADDR
		fi
	fi
	ifconfig $WAN_INTERFACE hw ether $WAN_MAC_ADDR
fi

if [ $ENABLE_WAN = 1 -a "$GATEWAY" = 'true' ]; then  #disconnect all wan  for vpn and wisp
	# stop vpn if enabled
	if [ -f $PLUTO_PID ];then
		ipsec setup stop
	fi
	killall l2tpd
	sleep 1
	killall l2tp.sh
	killall -9 pptp.sh
	killall -9 pppoe.sh
	rm -f /etc/ppp/first*
	disconnect.sh all
fi

# Start WLAN interface
NUM=0
while [ $NUM -lt $NUM_INTERFACE -a $ENABLE_BR = 1  ]
do
	echo 'Initialize '$WLAN_PREFIX$NUM' interface'
	$START_WLAN $WLAN_PREFIX$NUM
	NUM=`expr $NUM + 1`
done

if [ "$GATEWAY" = 'true' ]; then
	if [ $ENABLE_BR = 1 ]; then
		echo 'Setup BRIDGE interface'
		PIDFILE=/etc/udhcpc/udhcpc-$BR_INTERFACE.pid
		if [ -f $PIDFILE ] ; then
			PID=`cat $PIDFILE`
			if [ $PID != 0 ]; then
				kill -9 $PID
			fi
			rm -f $PIDFILE
		fi
		#kill syslogd and klogd
		killall syslogd
		killall klogd
		#Initialize bridge interface
		$START_BRIDGE $BR_INTERFACE $BR_LAN1_INTERFACE $WLAN_INTERFACE $BR_LAN2_INTERFACE
		eval `$GETMIB SCRLOG_ENABLED`
		if [ $SCRLOG_ENABLED != 0 -a $SCRLOG_ENABLED != 2 ] ;then
			eval `$GETMIB REMOTELOG_ENABLED`
			eval `$GETMIB REMOTELOG_SERVER`
			if [ $REMOTELOG_ENABLED = "1" ] ;then
				SYSLOG_PARA="-R $REMOTELOG_SERVER"
			fi
			syslogd -L $SYSLOG_PARA &
			klogd &
		fi

		# Set fixed IP or start DHCP server
		PIDFILE=/var/run/udhcpd.pid
		if [ -f $PIDFILE ] ; then
			PID=`cat $PIDFILE`
			if [ $PID != 0 ]; then
				kill -9 $PID
	        	fi
        		rm -f $PIDFILE
		fi

		eval `$GETMIB DHCP`
		if [ "$DHCP" = '0' ]; then
			eval `$GETMIB IP_ADDR`
			eval `$GETMIB SUBNET_MASK`
			eval `$GETMIB DEFAULT_GATEWAY`
			$SET_IP $BR_INTERFACE $IP_ADDR $SUBNET_MASK $DEFAULT_GATEWAY
			$START_WLAN_APP start $WLAN_INTERFACE $BR_INTERFACE

		elif [ "$DHCP" = '2' ]; then
			# caculate wait time
			NUM=0
			WAIT_TIME=0
			while [ $NUM -lt $NUM_INTERFACE  ]
			do
				eval `$GETMIB $WLAN_PREFIX$NUM WDS_ENABLED`
				if [ "$WDS_ENABLED" != 0 ]; then
					WAIT_TIME=`expr $WAIT_TIME + 5`
				else
					WAIT_TIME=`expr $WAIT_TIME + 1`
				fi
				NUM=`expr $NUM + 1`
			done
			sleep $WAIT_TIME

			$START_DHCP_SERVER $BR_INTERFACE gw
			$START_WLAN_APP start $WLAN_INTERFACE $BR_INTERFACE
		fi
	fi

	if [ $ENABLE_WAN = 1 ]; then
		if [ "$OP_MODE" != '1' ];then
			echo 'Setup WAN interface'
		fi

		# Initialize WAN interface
		# Delete DHCP client process
		DHCPC_WAN="$WLAN_INTERFACE eth1"
		for INTF in $DHCPC_WAN ; do
			PIDFILE=/etc/udhcpc/udhcpc-$INTF.pid
			if [ -f $PIDFILE ] ; then
				PID=`cat $PIDFILE`
				if [ $PID != 0 ]; then
					kill -9 $PID
				fi
				rm -f $PIDFILE
			fi
		done

		PIDFILE=/var/run/dnrd.pid
		if [ -f $PIDFILE ] ; then
			PID=`cat $PIDFILE`
			if [ $PID != 0 ]; then
				kill -9 $PID
	        	fi
        		rm -f $PIDFILE
		fi

		eval `$GETMIB WAN_DHCP`
		if [ "$OP_MODE" != '1' ];then  # not bridge mode
                   	ifconfig $WAN_INTERFACE up
			if [ "$WAN_DHCP" = '0' ]; then
				eval `$GETMIB WAN_IP_ADDR`
				eval `$GETMIB WAN_SUBNET_MASK`
				eval `$GETMIB WAN_DEFAULT_GATEWAY`
				$SET_IP $WAN_INTERFACE $WAN_IP_ADDR $WAN_SUBNET_MASK $WAN_DEFAULT_GATEWAY

				# start DNS relay
				eval `$GETMIB DNS1`
				if [ "$DNS1" != '0.0.0.0' ]; then
					DNS="-s $DNS1"
					echo "nameserver $DNS1" > /var/resolv.conf
					cat /etc/resolv.conf
				fi
				eval `$GETMIB DNS2`
				if [ "$DNS2" != '0.0.0.0' ]; then
					DNS="$DNS -s $DNS2"
				fi
				eval `$GETMIB DNS3`
				if [ "$DNS3" != '0.0.0.0' ]; then
					DNS="$DNS -s $DNS3"
				fi
				echo start DNS Relay Daemon
				dnrd $DNS
				upnp.sh
			elif [ "$WAN_DHCP" = '1' ]; then
				$START_DHCP_CLIENT $WAN_INTERFACE wait&
				upnp.sh
			elif [ "$WAN_DHCP" = '3' ]; then
				echo 'start PPPoE daemon'
				upnp.sh
				$START_PPPOE all $WAN_INTERFACE
			elif [ "$WAN_DHCP" = '4' ]; then
				echo 'start PPTP daemon'
				upnp.sh
				$START_PPTP $WAN_INTERFACE &
			elif [ "$WAN_DHCP" = '5' ]; then
				echo 'start L2TP daemon'
                upnp.sh
                $START_L2TP $WAN_INTERFACE &
			else
				echo 'Invalid DHCP MIB value for WAN interface!'
			fi
		fi

		# enable firewall when static ip
		if [ "$WAN_DHCP" = '0' ] || [ "$OP_MODE" = '1' ]; then
			echo 'Setup Firewall'
			$START_FIREWALL
		fi
		# static ip
		if [ -f /bin/vpn.sh ] && [ "$WAN_DHCP" != '4' ] && [ "$OP_MODE" != '1' ] &&  [ "$WAN_DHCP" = '0' ] ; then
			echo 'Setup VPN'
			vpn.sh all
		fi

		#enable ntp daemon , not brige mode
		if [ "$OP_MODE" != '1' ]; then
			killall $START_NTP > /dev/null
			$START_NTP
			$START_DDNS all &
		fi

	fi

else
	# Delete DHCP server/client process
	PIDFILE=/etc/udhcpc/udhcpc-$BR_INTERFACE.pid
	if [ -f $PIDFILE ] ; then
		PID=`cat $PIDFILE`
		if [ $PID != 0 ]; then
			kill -9 $PID
	       	fi
      		rm -f $PIDFILE
	fi

	PIDFILE=/var/run/udhcpd.pid
	if [ -f $PIDFILE ] ; then
		PID=`cat $PIDFILE`
		if [ $PID != 0 ]; then
			kill -9 $PID
       		fi
      		rm -f $PIDFILE
	fi

	#kill syslogd and klogd
	killall syslogd
	killall klogd

	#added for WA252(for second lan port) by Richard H.
	eval `$GETMIB OP_MODE`
	if [ "$OP_MODE" = '1' ];then
		$START_BRIDGE $BR_INTERFACE $BR_LAN1_INTERFACE $WLAN_INTERFACE $BR_LAN2_INTERFACE
	else
		$START_BRIDGE $BR_INTERFACE $BR_LAN1_INTERFACE $WLAN_INTERFACE
	fi

	eval `$GETMIB SCRLOG_ENABLED`
	if [ $SCRLOG_ENABLED != 0 -a $SCRLOG_ENABLED != 2 ]; then
		eval `$GETMIB REMOTELOG_ENABLED`
		eval `$GETMIB REMOTELOG_SERVER`
		if [ $REMOTELOG_ENABLED = "1" ] ;then
			SYSLOG_PARA="-R $REMOTELOG_SERVER"
		fi
		syslogd -L $SYSLOG_PARA &
		klogd &
	fi

	eval `$GETMIB DHCP`
	if [ "$DHCP" = '2' ]; then
		sleep 1
		$START_DHCP_SERVER $BR_INTERFACE ap
	fi

	if [ "$DHCP" = '0' ] || [ "$DHCP" = '2' ]; then
		$START_WLAN_APP start $WLAN_INTERFACE $BR_INTERFACE
	fi
fi

# start auto-discovery daemon
PIDFILE=/var/run/disc_server.pid
if [ -f $PIDFILE ] ; then
	PID=`cat $PIDFILE`
	if [ $PID != 0 ]; then
		kill -9 $PID
	fi
	rm -f $PIDFILE
fi

eval `$GETMIB AUTODISCOVERY_ENABLED`
if [ "$AUTODISCOVERY_ENABLED" != 0 ]; then
	disc_server $BR_INTERFACE &
fi

# cd ..
# ls
bin         etc         lost+found  sbin        usr         web
dev         lib         proc        tmp         var
# cd u# cd usr/
# ls
bin    share
# cd sh# cd share/
# ls
udhcpc
# cd ..
# cd b# cd bin/
# ls
[         bzcat     expr      killall   tail      wc
bunzip2   cut       head      nslookup  test
# cd ..
# ls
bin    share
# cd ..
# ls
bin         etc         lost+found  sbin        usr         web
dev         lib         proc        tmp         var
# cd b va# cd var/
# ls
autoconf-wlan0.fifo  iapp.fifo            run
autoconf.conf        lib                  state
etc                  log
# c cd e# cd etc/
# ls
# cd ..
# cd lo# cd log/
# ls
messages
# cd  cd ..
# cd r# cd run/
# ls
autoconf-wlan0.pid  iapp.pid            webs.pid
disc_server.pid     iwcontrol.pid
# cd ..
# ls
autoconf-wlan0.fifo  iapp.fifo            run
autoconf.conf        lib                  state
etc                  log
# cd s# cd state/
# ls
dhcp
# cd ..
# ls
autoconf-wlan0.fifo  iapp.fifo            run
autoconf.conf        lib                  state
etc                  log
# cd li# cd lib/
# ls
misc
# cd mi# cd misc/
# ls
# cd ..
# cd ..
# ls
autoconf-wlan0.fifo  iapp.fifo            run
autoconf.conf        lib                  state
etc                  log
# cd ..
# kls   ls
bin         etc         lost+found  sbin        usr         web
dev         lib         proc        tmp         var
# cd li# cd lib/
# ls
ld-uClibc.so.0  libc.so.0
# cd ..
# ls
bin         etc         lost+found  sbin        usr         web
dev         lib         proc        tmp         var
# cd p# cd proc/
# ls
1            517          bus          fs           meminfo      stat
2            549          cmdline      gpio         misc         swaps
3            555          cpuinfo      iomem        mounts       sys
4            556          devices      ioports      mtd          tty
425          6            dma          kcore        net          uptime
426          639          driver       kmsg         partitions   version
5            7            execdomains  loadavg      self         wlan0
503          8            filesystems  locks        slabinfo
# cd ..
# cd d# cd dev/
# ls
console  log      mtd      null     ttyS0    wl_chr0  wl_chr1
#   
# ls -als
   1 drwxr-xr-x    2 root     0            1024 Jan  1 00:00 .
   1 drwxr-xr-x   13 root     0            1024 Jan  1 00:00 ..
   0 crw-rw-rw-    1 root     0          4,  64 Jan  1 00:00 console
   0 srw-rw-rw-    1 root     0               0 Jan  1 00:00 log
   0 brw-rw-rw-    1 root     0         31,   0 May 13  2005 mtd
   0 crw-rw-rw-    1 root     0          1,   3 May 13  2005 null
   0 crw-rw-rw-    1 root     0          4,  64 Jan  1 00:06 ttyS0
   0 crw-rw-rw-    1 root     0         13,   0 May 13  2005 wl_chr0
   0 crw-rw-rw-    1 root     0         13,   1 May 13  2005 wl_chr1
# dd
dd: not found
# nest  tstat
netstat: not found
# top
top: not found
# ps
  PID  Uid     VmSize Stat Command
    1 root        248 S   init        
    2 root            SW  [keventd]
    3 root            SWN [ksoftirqd_CPU0]
    4 root            SW  [kswapd]
    5 root            SW  [bdflush]
    6 root            SW  [kupdated]
    7 root            SW  [mtdblockd]
    8 root        372 S   -sh 
  425 root        224 S   syslogd -L 
  426 root        216 S   klogd 
  503 root        220 R   autoconf -server -button -w wlan0 
  517 root        188 R   iapp br0 wlan0 
  549 root        180 S   disc_server br0 
  555 root        324 S   webs 
  556 root        140 S   udps 
  645 root        236 R   ps 
# pstree
pstree: not found
# free
free: not found
# df
df: not found
# reb# reboot 

The system is going down NOW !!
Sending SIGTERM to all processes.
Exiting Syslogd!
556: Terminated
555: Terminated
Terminated
# Sending Please stand by while rebooting the system.
Restarting system.
Shutdown network interface
wlan0:===>
br0: port 3(wlan0) entering disabled state
eth0:===>
br0: port 1(eth0) entering disabled state
eth1:===>
br0: port 2(eth1) entering disabled state
br0:===>
Enable Watch Dog to Reset whole system

UART1 output test ok
Uart init
mfid=000000c2 devid=00002249
Found 1 x 2M flash memory

---RealTek(RTL8186)at 2005.04.27-18:04+0800 version 1.3b [16bit](180MHz)
no sys signature at 00010000!

---Escape booting by user
<RealTek>