The purpose of this thread is to track changes in APPro software for Atheros 531x-based devices.
The firmware is available in two versions:
* for devices with Wistron bootloader, like Appro5003, Ovislink WLA5000, or RDAA81
* for devices with RedBoot bootloader, like APPro5003v2 PCB, APPro Outdoor5, or Ubiquiti
Files with APPro firmware are named in following fashion:
appro5003v2-dd-mm-yyyy-revxxx-zzz.bin
where:
* dd-mm-yyyy - release date
* xxx - number of compilation
* zzz - bootloader version:
rdaa81 - firmware for APPro5003, RDAA81, Ovislink 5000, and compatible
ubnt - firmware for APPro5003v2 PCB, Outdoor5, Ubiquiti WISP Station, and Ubiquiti Lite Station
Mini-FAQ
What file should I use for my device?
To check the version of installed firmware, open Access Point Status page and look up Compilation line in System section.
* if the line contains 2.4.34-appro, use these files: appro5003v2-dd-mm-yyyy-revxxx-rdaa81.bin
* if the line contains 2.4.27-appro, install these files: appro5003v2-dd-mm-yyyy-revxxx-ubnt.bin
Does this firmware work on devices with (or without) HW module?
Currently available software supports devices with hardware modules, as well as with softlicenses
Are the upgrades free?
* upgrades within a standard feature set are free of charge.
* custom, client-specific upgrades are developed for a fee
(contact us for more detail)
How to upgrade APPro5000/5003 firmware to APPro5003v2?
Upgrade procedure will be available shortly.
Are different APPro firmware versions compatible?
* APPro5003v2 and APPro5000/5003 are not compatible and configuration files should not be transferred between these versions of APPro software.
* APPro5003v2 and APPro Outdoor5 software versions are based on the same code and are compatible.
* we give our best efforts to maintain backward compatibility (which means that when you install new firmware version, old configuration will be preserved), but this policy does not always apply to configuration files downloaded from devices. If you store device configuration files, we recommend re-downloading such files after each upgrade.
* we cannot guarantee configuration compatibility for downgrades - for more info please consult changelogs and release notes.
* user-modified scripts and direct edits to configuration files may cause problems after firmware upgrades. In such cases we recommend performing an upgrade in such way, that if the problems occur, the user should be able to reconfigure the device.
To upgrade via device's Web interface, use files with .bin extension only! Files with .tftp extension are intended for recovery purposes only, or first installation of the software. Remember to use only upgrade files that are compatible with your hardware
Latest version available at the time of writing this information is:
* improved encryption for AP/APC mode with APPro5000 devices
* improved TFM operation with NAT enabled
* improved Multipoint Bridge mode
* added option for region changes
* fixed problem with config change confirmation page
* improved ACL operation
* added regions for 4,9 GHz and 5-6 GHz bands
* fixed MAC acquisition from factory setup
* added IP address info on Active Clients list
* added enabling/disabling LEDs for RDAA81 (disabled by default)
* fixed Site Survey for regdomain 1001
* added Rate Algorithm feature
* added Dynamic ACK feature
* added Use TFM MACs in ACL option
* added LAN 0 Access Control feature
* maximum RTS value increased to 2347
* added Web Server Port, Telnet Port, and SSH Port options
* latest Web pages integrated into firmware
* removed 0.5 dBm Tx Power steps
* new transfer statistics
* fixed upload of config files with spaces in filenames
* removed unneeded QoS modifications (regarding 2405)
* added Brazilian - Portuguese, Czech, and Polish languages in Web interface.
* added temperature graphs (for devices equipped with APPro hardware module)
* added voltage graphs (for devices equipped with APPro hardware module)
* Active Client List now shows ACL and/or TFM comments
* Connection Tracking page now shows the number of active TCP connections
* added graphs of CPU load, memory usage and number of running tasks
* added selection of hardware platform
* added selection of antenna polarization on UBNT devices
* added ARP filter feature
* improved operation of static ARP
* improved support for 64-character keys in WPA/WPA2
* improved support for WPA/WPA2 keys with nonstandard characters
Nie możesz pisać nowych tematów Nie możesz odpowiadać w tematach Nie możesz zmieniać swoich postów Nie możesz usuwać swoich postów Nie możesz głosować w ankietach Nie możesz załączać plików na tym forum Możesz ściągać załączniki na tym forum
